- 您現在的位置：買賣IC網 > PDF目錄67684 > IBM25PPC970FX6UB267ET 64-BIT, 1800 MHz, RISC PROCESSOR, CBGA576 PDF資料下載
參數資料
| 型號： | IBM25PPC970FX6UB267ET |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 64-BIT, 1800 MHz, RISC PROCESSOR, CBGA576 |
| 封裝： | 25 X 25 MM, 1 MM PITCH, CERAMIC, BGA-576 |
| 文件頁數： | 72/78頁 |
| 文件大?。?/td> | 3524K |
| 代理商： | IBM25PPC970FX6UB267ET |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁當前第72頁第73頁第74頁第75頁第76頁第77頁第78頁
Datasheet
PowerPC 970FX RISC Microprocessor
System Design Information
Page 74 of 78
Version 2.5
March 26, 2007
TBEN
1
In
System: time base enable.
—
TCK
1
In
JTAG: test clock that is separate from the system clock. Controls all
test access port functions.
TDI
1
In
JTAG: serial input used to feed test data and test access port instruc-
tions.
TDO
1
Out
JTAG: Serial output used to extract data from the chip under test con-
trol.
—
THERM_INT
1
In
System: external thermal interrupt when low.
—
TMS
1
In
JTAG: Select used to control the operation of the JTAG state
machine.
—
TRIGGERIN
1
In
External trigger to start trace collection.
—
TRIGGEROUT
1
Out
Signal that indicates that internal trace collection has begun.
—
TRST
1
In
JTAG: asynchronous reset for the JTAG state machine.
Table 5-8. Input/Output Signal Descriptions (Page 4 of 4)
Pin Name
Width
In/Out
System/Debug Function
Notes
Notes:
1. These are test signals for factory use only and must be pulled up to OVDD for normal processor operation.
2. For I2C or JTAG operation, the TCK and TDI signals must be pulled down to ground with a 10 k
Ω resistor. See Section 3.10.3 on
page 43.
3. Bus ratios 8:1 and 16:1 are not supported for PI Input functionality.
4. These are test signals for factory use only and must be pulled down to GND for normal processor operation.
5. This signal should not be connected.
6. These pins can be used to measure on-chip voltage drop and noise. They should be connected to a backside probe point
immediately behind the module. They should not be connected to GND and VDD planes.
7. BiDi = bidirectional. OD = open drain.
8. Using the 4:1 or 12:1 ratio with multiplier of 12 limits the use of power tuning to (frequency)/2.
9. The PLL_MULT and PLL_RANGE(1:0) bits can be overwritten by JTAG commands and the BUS_CFG bits can be changed by
SCOM commands during the POR sequence. See the PowerPC 970FX Power On Reset Application Note for more details
10. Must be pulled down with a 10 k
Ω resistor to GND.
11. The TRST signal must be pulled up to OVDD with a 10 kΩ resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| IBM25PPC970MP7TR21AFT | 64-BIT, 1600 MHz, RISC PROCESSOR, CBGA575 |
| IBM26BL486DX2-V66QP | 32-BIT, 66 MHz, MICROPROCESSOR, PQFP208 |
| IBM26BL486DX2-V80QP | 32-BIT, 80 MHz, MICROPROCESSOR, PQFP208 |
| IBM26BL486DX2-V50GP | 32-BIT, 50 MHz, MICROPROCESSOR, CPGA168 |
| IBM26BL486DX2-V50QP | 32-BIT, 50 MHz, MICROPROCESSOR, PQFP208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBM25PPC970FX6UB429RT | 制造商:IBM Microelectronics 功能描述:MPU 970FX RISC 64BIT 90NM 1.5V 576CBGA - Trays 制造商:IBM 功能描述:IBM IBM25PPC970FX6UB429RT Co-Processors |
| IBM25PPC970GX7TR01-ET | 制造商:IBM 功能描述:ANTARES GX DD1.0X 1.2GHZ POWER OPTIMIZED - Trays |
| IBM25PPC970GX7TR05-ET | 制造商:IBM 功能描述:ANTARES GX DD1.0X 1.4GHZ POWER OPTIMIZED - Trays |
| IBM25PPC970GX7TR20-ET | 制造商:IBM Microelectronics 功能描述:ANTARES GX DD1.0X 1.6GHZ POWER OPTIMIZED - Trays |
| IBM25PPC970GX7TR23-ET | 制造商:IBM 功能描述:ANTARES GX DD1.0X 1.6GHZ PERFORMANCE OPTIMIZED - Trays |
發布緊急采購，3分鐘左右您將得到回復。