- 您現在的位置：買賣IC網 > PDF目錄370311 > GCIXP1250-200 Microprocessor PDF資料下載
參數資料
| 型號： | GCIXP1250-200 |
| 英文描述： | Microprocessor |
| 中文描述： | 微處理器 |
| 文件頁數： | 12/148頁 |
| 文件大小： | 1601K |
| 代理商： | GCIXP1250-200 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁
Intel
IXP1250 Network Processor
12
Datasheet
2.4
FBI Unit and the IX Bus
The FBI Unit is responsible for servicing fast peripherals, such as MAC-layer devices, on the IX
Bus. This includes moving data to and from the IXP1250 Receive and Transmit FIFOs.
The IX Bus provides a 4.4 Gbps interface to peripheral devices. The IX Bus was specifically
designed to provide a simple and efficient interface. The IX Bus can be configured as either a
64-bit bidirectional bus or as two 32-bit unidirectional buses. The maximum operating frequency
of the IX Bus is 104 MHz.
Two IXP1250 devices can be placed on a single IX Bus in shared IX Bus mode. This option is
supported only in 64-bit bidirectional mode.
The FBI Unit contains the Transmit and Receive FIFO elements, control and status registers
(CSRs), a 4 Kbyte Scratchpad RAM, and a Hash Unit for generating 48- and 64-bit hash keys. It
also contains the drivers and receivers for the IX Bus.
The IX Bus consists of 64 data pins, 23 control pins, and a clock input pin. A sideband bus
operating in parallel to the IX Bus, called the Ready Bus, consists of eight additional data pins and
five control pins.
The Ready Bus is synchronous to the IX Bus clock, but operation is controlled by a programmable
hardware sequencer. Ready Bus cycles are separate and distinct from IX Bus cycles. Up to twelve
sequencer commands are loaded at chip initialization time, and run in a continuous loop. The
commands can consist of sampling FIFO status for the IX Bus devices, sending Flow Control
messages to MAC devices, and reads/writes to other IXP1250 devices as required by the
application design. Refer to the
IXP1250 Network Processor Hardware Reference Manual
for
specific details on using the Ready Bus.
2.4.1
IX Bus Access Behavior
There are two basic modes of IX Bus operation. This is a configuration option only and is not
intended to be used
“
on the fly
”
to switch between modes.
64-Bit Bidirectional Mode
The entire 64-bit data path FDAT[63:0] is used for reads or writes to IX Bus devices. The
IXP1250 always drives and receives all 64 bits of the IX Bus in this mode. Valid bytes are
indicated on the FBE_L[7:0] signals driven by the IXP1250 during writes and by the IX Bus
slave device on reads.
32-Bit Unidirectional Mode
The IX Bus is split into independent 32-bit transmit and 32-bit receive data paths. Transmit
data is driven on FDAT[63:32] and receive data is input on FDAT[31:0]. In this mode, the
transmit path is always driven. The receive path is an input during receive cycles and driven by
the IXP1250 during device reset cycles or during prolonged idle time on the bus. Valid bytes
are identified for the transmit path by the FBE_L[7:4] signals. Valid bytes are identified for the
receive path by the FBE_L[3:0] signals.
Each basic mode has two additional modes depending on the number of IX Bus devices and ports
being used: 1-2 MAC mode for one or two slave devices, and 3+ MAC mode when using three to
seven slave devices. Bus timing and the functions of the IX Bus signals are slightly different in
each mode. These functional definitions per IX Bus mode are listed in
Section 3.6
and
Section 3.7
.
相關PDF資料 |
PDF描述 |
|---|---|
| GCIXP1250-232 | Microprocessor |
| GCK101 | Analog IC |
| GCK131 | Microcontroller |
| GCM-3.15A | Fuse |
| GCM-4A | Fuse |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GCIXP1250BA | 功能描述:IC MPU NETWORK 166MHZ 520-BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:40 系列:MPC83xx 處理器類型:32-位 MPC83xx PowerQUICC II Pro 特點:- 速度:267MHz 電壓:0.95 V ~ 1.05 V 安裝類型:表面貼裝 封裝/外殼:516-BBGA 裸露焊盤 供應商設備封裝:516-PBGAPGE（27x27） 包裝:托盤 |
| GCIXP1250BB | 功能描述:IC MPU NETWORK 200MHZ 520-BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:40 系列:MPC83xx 處理器類型:32-位 MPC83xx PowerQUICC II Pro 特點:- 速度:267MHz 電壓:0.95 V ~ 1.05 V 安裝類型:表面貼裝 封裝/外殼:516-BBGA 裸露焊盤 供應商設備封裝:516-PBGAPGE（27x27） 包裝:托盤 |
| GCIXP1250BC | 功能描述:IC MPU NETWORK 232MHZ 520-BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:40 系列:MPC83xx 處理器類型:32-位 MPC83xx PowerQUICC II Pro 特點:- 速度:267MHz 電壓:0.95 V ~ 1.05 V 安裝類型:表面貼裝 封裝/外殼:516-BBGA 裸露焊盤 供應商設備封裝:516-PBGAPGE（27x27） 包裝:托盤 |
| GCJ0335C5C0JR50D | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Chip Monolithic Ceramic Capacitors |
| GCJ0335C5C1AR50D | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Chip Monolithic Ceramic Capacitors |
發布緊急采購，3分鐘左右您將得到回復。