- 您現在的位置：買賣IC網 > PDF目錄67592 > FUSION878A (CONEXANT SYSTEMS) COLOR SIGNAL DECODER, PQFP128 PDF資料下載
參數資料
| 型號： | FUSION878A |
| 廠商： | CONEXANT SYSTEMS |
| 元件分類： | 顏色信號轉換 |
| 英文描述： | COLOR SIGNAL DECODER, PQFP128 |
| 封裝： | PLASTIC, QFP-128 |
| 文件頁數： | 8/180頁 |
| 文件大?。?/td> | 2067K |
| 代理商： | FUSION878A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁
Fusion 878A
3.0 Electrical Interfaces
PCI Video Decoder
3.4 I2C Interface
100600B
Conexant
3-21
3.4 I2C Interface
The I2C bus is a two-wire serial interface. Serial clock and data lines, SCL, and
SDA transfer data between the bus master and the slave device. The I2C bus
within the Fusion 878A supports repeated starts, up to 396.8 kHz timing, and
multi-byte sequential transactions. The I2CRATE signal specifies either 99.2 kHz
or 396.8 kHz timing rate.
If the PCI clock runs at less than the maximum rate,
these rates will slow down proportionately. For details on the I2C register, see
The relationship between SCL and SDA is decoded to provide both a start and
stop condition on the bus. To initiate a transfer on the I2C bus, the master must
transmit a start pulse to the slave device. This is accomplished by taking the SDA
line low while the SCL line is held high. The master should generate a start pulse
only at the beginning of the cycle, or after the transfer of a data byte to or from the
slave. To terminate a transfer, the master must take the SDA line high while the
SCL line is held high. The master may issue a stop pulse at any time during an
I2C cycle. Since the I2C bus interprets any transition on the SDA line during the
high phase of the SCL line as a start or stop pulse, care must be taken to ensure
that data is stable during the high phase of the clock. This is illustrated in
An I2C write transaction consists of sending a START signal, 2 or 3 bytes of
data (checking for a receiver acknowledge after each byte), and a STOP signal.
The write data is supplied from a 24-bit register with bytes I2CDB0, I2CDB1,
and I2CDB2. This 24-bit register is shifted left to provide data serially, with the
MSB as the first bit. An I2C write occurs when the R/W bit in the I2CDB0[0] is
set to a logical low. The system driver can write 2 or 3 bytes of data by selecting
the appropriate value for I2CW3BRA bit.
An I2C read transaction consists of sending a START signal, 1 byte of data
(checking for a receiver acknowledge), reading 1 data byte from the slave,
sending the master NACK, and sending the STOP signal. The data read is shifted
into the I2CDB2 register. An I2C read occurs when the R/W bit in the I2CDB0[0]
is set to a logical 1, illustrated in Figure 3-15.
When the read or write operation is completed, the Fusion 878A sends an
interrupt over the PCI bus to the host controller. The status bit RACK will
indicate if the operation completed successfully with the correct number of slave
acknowledges.
Figure 3-14. The Relationship Between SCL and SDA
Start
Stop
SDA
SCL
879A_045
相關PDF資料 |
PDF描述 |
|---|---|
| FVXO-HC53BR-FREQ | VCXO, CLOCK, 0.75 MHz - 250 MHz, HCMOS OUTPUT |
| FVXO-HC72BR-FREQ | VCXO, CLOCK, 0.75 MHz - 180 MHz, HCMOS OUTPUT |
| FVXO-HC73B-FREQ | VCXO, CLOCK, 0.75 MHz - 250 MHz, HCMOS OUTPUT |
| FVXO-LC52BR-FREQ | VCXO, CLOCK, 0.75 MHz - 1000 MHz, LVDS OUTPUT |
| FVXO-LC72BR-FREQ | VCXO, CLOCK, 0.75 MHz - 1000 MHz, LVDS OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FUSZ03 | 制造商:Honeywell Sensing and Control 功能描述: |
| FUTURE 1AA PLUS | 制造商:Ansmann 功能描述: 制造商:ANSMANN AG 功能描述: |
| FUTURE 2AA PLUS | 制造商:Ansmann 功能描述: 制造商:ANSMANN AG 功能描述: |
| FUTURE 2C PLUS | 制造商:Ansmann 功能描述: 制造商:ANSMANN AG 功能描述: |
| FUTURE 3D PLUS | 制造商:Ansmann 功能描述: 制造商:ANSMANN AG 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。