- 您現在的位置：買賣IC網 > PDF目錄380224 > CYP15G0403DXB (Cypress Semiconductor Corp.) Independent Clock Quad HOTLink II Transceiver(獨立時鐘，四熱連接II收發器) PDF資料下載
參數資料
| 型號： | CYP15G0403DXB |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | Independent Clock Quad HOTLink II Transceiver(獨立時鐘，四熱連接II收發器) |
| 中文描述： | 獨立時鐘四路HOTLink II收發器（獨立時鐘，四熱連接二收發器） |
| 文件頁數： | 20/43頁 |
| 文件大小： | 744K |
| 代理商： | CYP15G0403DXB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
CYV15G0403DXB
CYW15G0403DXB
CYP15G0403DXB
Document #: 38-02065 Rev. *E
Page 20 of 43
SDASEL1A[1:0]
SDASEL1B[1:0]
SDASEL1C[1:0]
SDASEL1D[1:0]
Primary Serial Data Input Signal Detector Amplitude Select
. The initialization value of the SDASEL1x[1:0]
latch = 10. SDASEL1x[1:0] selects the trip point for the detection of a valid signal for the INx1± Primary
Differential Serial Data Inputs.
When SDASEL1x[1:0] = 00, the Analog Signal Detector is disabled.
When SDASEL1x[1:0] = 01, the typical p-p differential voltage threshold level is 140 mV.
When SDASEL1x[1:0] = 10, the typical p-p differential voltage threshold level is 280 mV.
When SDASEL1x[1:0] = 11, the typical p-p differential voltage threshold level is 420 mV.
Secondary Serial Data Input Signal Detector Amplitude Select
. The initialization value of the
SDASEL2x[1:0] latch = 10. SDASEL2x[1:0] selects the trip point for the detection of a valid signal for the INx2±
Secondary Differential Serial Data Inputs.
When SDASEL2x[1:0] = 00, the Analog Signal Detector is disabled
When SDASEL2x[1:0] = 01, the typical p-p differential voltage threshold level is 140 mV.
When SDASEL2x[1:0] = 10, the typical p-p differential voltage threshold level is 280 mV.
When SDASEL2x[1:0] = 11, the typical p-p differential voltage threshold level is 420 mV.
Transmit Encoder Bypassed
. The initialization value of the ENCBYPx latch = 1. ENCBYPx selects if the
Transmit Encoder is enabled or bypassed. When ENCBYPx = 1, the Transmit encoder is enabled. When
ENCBYPx = 0, the Transmit Encoder is bypassed and raw 10-bit characters are transmitted.
SDASEL2A[1:0]
SDASEL2B[1:0]
SDASEL2C[1:0]
SDASEL2D[1:0]
ENCBYPA
ENCBYPB
ENCBYPC
ENCBYPD
TXCKSELA
TXCKSELB
TXCKSELC
TXCKSELD
Transmit Clock Select
. The initialization value of the TXCKSELx latch = 1. TXCKSELx selects the clock
source used to write data into the Transmit Input Register. When TXCKSELx = 1, the associated input register,
TXDx[7:0] and TXCTx[1:0], is clocked by REFCLKx
↑.
In this mode, the phase alignment buffer in the transmit
path is bypassed. When TXCKSELx = 0, the associated TXCLKx
↑
is used to clock in the input registers,
TXDx[7:0] and TXCTx[1:0].
Transmit PLL Clock Rate Select
. The initialization value of the TXRATEx latch = 0. TXRATEx is used to
select the clock multiplier for the Transmit PLL. When TXRATEx = 0, each transmit PLL multiples the
associated REFCLKx± input by 10 to generate the serial bit-rate clock. When TXRATEx = 0, the TXCLKOx
output clocks are full-rate clocks and follow the frequency and duty cycle of the associated REFCLKx± input.
When TXRATEx = 1, each Transmit PLL multiplies the associated REFCLKx± input by 20 to generate the
serial bit-rate clock. When TXRATEx = 1, the TXCLKOx output clocks are twice the frequency rate of the
REFCLKx± input. When TXCKSELx = 1 and TXRATEx = 1, the Transmit Data Inputs are captured using both
the rising and falling edges of REFCLKx. TXRATEx = 1 and SPDSELx is LOW, is an invalid state and this
combination is reserved.
Reframe Enable
. The initialization value of the RFENx latch = 1. RFENx selects if the receiver framer is
enabled or disabled. When RFENx = 1, the associated channel’s framer is enabled to frame per the presently
enabled framing mode and selected framing character. When RFENx = 0, the associated channel’s framer is
disabled, and no received bits alters the frame offset.
Receive Channel Enable
. The initialization value of the RXPLLPDx latch = 0. RXPLLPDx selects if the
associated receive channel is enabled or powered-down. When RXPLLPDx = 0, the associated PLL and
analog circuitry is powered-down. When RXPLLPDx = 1, the associated PLL and analog circuitry is enabled.
TXRATEA
TXRATEB
TXRATEC
TXRATED
RFENA
RFENB
RFENC
RFEND
RXPLLPDA
RXPLLPDB
RXPLLPDC
RXPLLPDD
RXBISTA
RXBISTB
RXBISTC
RXBISTD
TXBISTA
TXBISTB
TXBISTC
TXBISTD
OE2A
OE2B
OE2C
OE2D
Receive Bist Disabled
. The initialization value of the RXBISTx latch = 1. RXBISTx selects if receive BIST is
disabled or enabled. When RXBISTx = 1, the receiver BIST function is disabled. When RXBISTx = 0, the
receive BIST function is enabled.
Transmit Bist Disabled
. The initialization value of the TXBISTx latch = 1. TXBISTx selects if the transmit
BIST is disabled or enabled. When TXBISTx = 1, the transmit BIST function is disabled. When TXBISTx = 0,
the transmit BIST function is enabled.
Secondary Differential Serial Data Output Driver Enable
. The initialization value of the OE2x latch = 0.
OE2x selects if the OUT2± secondary differential output drivers are enabled or disabled. When OE2x = 1, the
associated serial data output driver is enabled allowing data to be transmitted from the transmit shifter. When
OE2x = 0, the associated serial data output driver is disabled. When a driver is disabled via the configuration
interface, it is internally powered down to reduce device power. If both serial drivers for a channel are in this
disabled state, the associated internal logic for that channel is also powered down. A device reset (RESET
sampled LOW) disables all output drivers.
Table 9. Device Configuration and Control Latch Descriptions
(continued)
Name
Signal Description
相關PDF資料 |
PDF描述 |
|---|---|
| CYV15G0403DXB | Independent Clock Quad HOTLink II Transceiver(獨立時鐘，四熱連接II收發器) |
| CYW15G0403DXB | Independent Clock Quad HOTLink II Transceiver(獨立時鐘，四熱連接II收發器) |
| CYRF69103 | Programmable Radio on Chip Low Power |
| CYRF69213 | Programmable Radio on Chip Low Power |
| CYRF69213-40LFXC | Programmable Radio on Chip Low Power |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYP15G0403DXB_07 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II⑩ Transceiver |
| CYP15G0403DXB_09 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II Transceiver |
| CYP15G0403DXB_11 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II Transceiver Single 3.3V supply |
| CYP15G0403DXB-BGC | 功能描述:電信線路管理 IC Quad Indep Channel XCVR COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CYP15G0403DXB-BGI | 功能描述:電信線路管理 IC Quad Indep Channel XCVR IND RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。