- 您現在的位置：買賣IC網 > PDF目錄364674 > AMIS-53000-M Frequency Agile Transceiver PDF資料下載
參數資料
| 型號： | AMIS-53000-M |
| 英文描述： | Frequency Agile Transceiver |
| 中文描述： | 捷變頻收發器 |
| 文件頁數： | 35/99頁 |
| 文件大小： | 2638K |
| 代理商： | AMIS-53000-M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
AMIS-53000
Frequency Agile Transceiver
Data Sheet
6.1.4.5.
Interface Options
Table 16: I
2
C Address Auto Increment
Register
Number (HEX)
0X0C
Name
General Options A
Bits
3
5,4
3
Function
Disable the internal pull up resistors on SDATA and SSN lines
Select a clock rate for the interface when the AMIS-53000 is master
Disable auto increment for I
2
C control interface register addressing
0X0D
General Options B
Additional interface options give the AMIS-53000 the flexibility to tailor the interface to specific requirements. These options are
available in the interface options register, and can be stored into EE at board assembly to best suit the application.
6.1.4.6.
Pull Up Disable
The AMIS-53000 includes built in pull up resistors for use with the I
2
C operation to reduce the overall system component count. The
pull ups are asserted at POR until mode selection occurs. If mode is determined to be 3-wire, the pull ups are removed. If mode is
determined to be I
C, this option bit determines whether the pull ups are to be removed.
6.2 Command Register
The AMIS-53000 contains a single 8-bit register that allows single writes to the register to place the AMIS-53000 into a desired mode.
It is very important to remember that all registers associated with that mode must be preprogrammed for the single write to this register
to operate correctly.
The command register allows the user application to issue a single register write to the AMIS-53000 to initiate the function listed in
Table 17. When the function is started, the AMIS-53000 uses the register values associated with the function selected as the
parameters of the function. These register values will be the default values or the values the user application has written to the
registers before the function is called out in the command register.
Table 17: Command - 0X00 [0]
Bit
Command
Comment
[7:4]
[3:0]
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1111
Global Reset
Resets the part completely
[7:6]
[5:0]
XXXXXX
100000
Conversion
XXXXXX
100000
Conversions
Standby is both a state for the transceiver, and a command given to the transceiver. The actual operation of standby mode can be
either a low-power mode where all internal circuitry of the AMIS-53000 except for the interface will be disabled, or a clock-only mode
where the crystal oscillator will be enabled to continue providing a system clock for an external microprocessor. A bit available in the
general options A register allows selection of power-down or clock-only operation in standby mode.
0000
Standby
Receive
Transmit
Idle
Idle Return
Write EE
Read EE
Calibrate QS Osc
Calibrate RC
Calibrate PLL
Calibrate LNA
ROM2Regs
Put the part into standby
Put the part into receive mode
Put the part into transmit mode
Put the part into idle mode
Use to return to idle after interrupt for HK or receive during sniff
Write the content of the working registers into EE
Read the contents of the EE
Calibrates the Quick Start oscillator
Calibrates the 10kHz RC oscillator
Calibrates the PLL
Calibrates the LNA matching
Write the content of the ROM into the shadow registers
01
Single ADC
Do an ADC one time on the channel selected loop filter output
11
Continuous ADC
Do an ADC on the channel selected continuously loop filter output
35
AMI Semiconductor
– Aug. 05, Rev. 1.0
www.amis.com
相關PDF資料 |
PDF描述 |
|---|---|
| AMIS-53050 | Frequency Agile Transceiver |
| AMIS-710650 | Color CIS Module Analog Video Output |
| AMIS-710650-A6 | Color CIS Module Analog Video Output |
| AMIS-710651 | Color CIS Module |
| AMIS-710651-A4 | Color CIS Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-53050 | 制造商:ON Semiconductor 功能描述:WIRELESS LOW POWER TRANSC - 300-960MHZ, XTRA LOW RX PW, LQFP - Trays 制造商:ON Semiconductor 功能描述:WIRELESS LOW POWER TRANSC - 300-960MHZ, XTRA LOW RX PW, LQFP - Tape and Reel 制造商:ON Semiconductor 功能描述:WIRELESS LP TRANSC - 300-960MHZ, SPI INTERFACE:GANG XC, LQFP - Trays 制造商:ON Semiconductor 功能描述:WIRELESS LP TRANSC - 300-960MHZ, SPI INTERFACE:GANG XC, LQFP - Tape and Reel |
| AMIS-53050-I/A | 制造商:AMI 制造商全稱:AMI 功能描述:Frequency Agile Transceiver |
| AMIS-53050-XTD | 功能描述:射頻收發器 AMIS-53050 WLESS TRNSCVR RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| AMIS-70020 | 制造商:ON Semiconductor 功能描述:POWER FAILURE ELAPSED TIME COUNTER, SOIC - Rail/Tube 制造商:ON Semiconductor 功能描述:POWER FAILURE ELAPSED TIME COUNTER, SOIC - Tape and Reel |
| AMIS-710200 | 制造商:AMI 制造商全稱:AMI 功能描述:200dpi CIS Module |
發布緊急采購，3分鐘左右您將得到回復。