參數資料
型號: AM79C971
廠商: Advanced Micro Devices, Inc.
英文描述: PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus
中文描述: PCnet⑩快速單芯片全雙工10/100 Mbps以太網控制器,PCI總線
文件頁數: 24/265頁
文件大?。?/td> 3190K
代理商: AM79C971
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁
24
Am79C971
nibble of the frame. TX_EN transitions synchronous to
TX_CLK rising edges.
Note:
The TX_EN pin is multiplexed with the TXEN
pin.
When RST is active, TX_EN is an input for NAND tree
testing
.
If the MII port is not selected, the TX_EN pin can be left
floating.
TX_ER
Transmit Error
TX_ER is an output that, if asserted while TX_EN is as-
serted, instructs the MII PHY device connected to the
Am79C971 device to transmit a code group error.
TX_ER is unused and is reserved for future use and will
always be driven to a logical zero.
Output
When RST is active, TX_ER is an input for NAND tree
testing
.
If the MII port is not selected, the TX_ER pin can be left
floating.
COL
Collision
COL is an input that indicates that a collision has been
detected on the network medium.
Input
Note:
The COL pin is multiplexed with the CLSN pin.
When RST is active, COL is an input for NAND tree
testing
.
If the MII port is not selected, the COL pin can be left
floating.
CRS
Carrier Sense
CRS is an input that indicates that a non-idle medium,
due either to transmit or receive activity, has been de-
tected.
Input
Note:
The CRS pin is multiplexed with the RXEN pin.
When RST is active, CRS is an input for NAND tree
testing
.
If the MII port is not selected, the CRS pin can be left
floating.
RX_CLK
Receive Clock
RX_CLK is a clock input that provides the timing refer-
ence for the transfer of the RX_DV, RXD[3:0], and
RX_ER signals into the Am79C971 device. RX_CLK
must provide a nibble rate clock (25% of the network
data rate). Hence, an MII transceiver operating at 10
Mbps must provide an RX_CLK frequency of 2.5 MHz
and an MII transceiver operating at 100 Mbps must pro-
vide an RX_CLK frequency of 25 MHz. When the exter-
Input
nal PHY switches the RX_CLK and TX_CLK, it
must
provide glitch-free clock pulses.
Note:
The RX_CLK pin is multiplexed with the RXCLK
pin.
When RST is active, RX_CLK is an input for NAND tree
testing
.
If the MII port is not selected, the RX_CLK pin can be
left floating.
RXD[3:0]
Receive Data
RXD[3:0] is the nibble-wide MII receive data bus. Data
on RXD[3:0] is sampled on every rising edge of
RX_CLK while RX_DV is asserted. RXD[3:0] is ignored
while RX_DV is de-asserted.
Input
When the EADI is enabled (EADISEL, BCR2, bit 3) and
the Receive Frame Tagging is enabled (RXFRTG,
CSR7, bit 14) and the MII is
not
selected, the RXD[0]
pin becomes a data input pin for the Receive Frame
Tag (RXFRTGD). See the
Receive Frame Tagging
sec-
tion for details.
Note:
The RXD[0] pin is multiplexed with the
RXFRTGD pin.
When RST is active, RXD[3:0] are inputs for NAND tree
testing
.
If the MII port is not selected, the RXS[3:0] pin can be
left floating.
RX_DV
Receive Data Valid
RX_DV is an input used to indicate that valid received
data is being presented on the RXD[3:0] pins and
RX_CLK is synchronous to the receive data. In order
for a frame to be fully received by the Am79C971 de-
vice on the MII, RX_DV must be asserted prior to the
RX_CLK rising edge, when the first nibble of the Start
of Frame Delimiter is driven on RXD[3:0], and must re-
main asserted until after the rising edge of RX_CLK,
when the last nibble of the CRC is driven on RXD[3:0].
RX_DV must then be deasserted prior to the RX_CLK
rising edge which follows this final nibble. RX_DV tran-
sitions are synchronous to RX_CLK rising edges.
Input
When the EADI is enabled (EADISEL, BCR2, bit 3), the
Receive Frame Tagging is enabled (RXFRTG, CSR7,
bit 14), and the MII is
not
selected, the RX_DV pin be-
comes a data input enable pin for the Receive Frame
Tag (RXFRTGE). See the
Receive Frame Tagging
sec-
tion for details.
Note:
The RX_DV pin is multiplexed with the
RXFRTGE pin.
When RST is active, RX_DV is an input for NAND tree
testing
.
相關PDF資料
PDF描述
AM79C971KCW IC LOGIC 16211 24-BIT FET BUS SWITCH -40+85C TSSOP-56 35/TUBE
AM79C972BKCW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972BKIW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972BVCW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972 PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
相關代理商/技術參數
參數描述
AM79C971AKC 制造商:Advanced Micro Devices 功能描述:
AM79C971AVC 制造商:Advanced Micro Devices 功能描述:10/100 MBPS ETHERNET - Trays
AM79C971AVC\\W 制造商:Rochester Electronics LLC 功能描述:- Bulk
AM79C971AVC\W 制造商:Rochester Electronics LLC 功能描述:- Bulk
AM79C971AWW WAF 制造商:Advanced Micro Devices 功能描述: