- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C971 (Advanced Micro Devices, Inc.) PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus PDF資料下載
參數資料
| 型號： | AM79C971 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
| 中文描述： | PCnet⑩快速單芯片全雙工10/100 Mbps以太網控制器，PCI總線 |
| 文件頁數： | 21/265頁 |
| 文件大?。?/td> | 3190K |
| 代理商： | AM79C971 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁
Am79C971
21
larity is programmed to active HIGH, the output is a
totem pole driver.
Note:
The LED1 pin is multiplexed with the EESK and
SFBD pins.
The LED1 pin is also used during EEPROM Auto-
Detection to determine whether or not an EEPROM is
present at the Am79C971 controller interface. At the
last rising edge of CLK while RST is active LOW, LED1
is sampled to determine the value of the EEDET bit in
BCR19. It is important to maintain adequate hold time
around the rising edge of the CLK at this time to ensure
a correctly sampled value. A sampled HIGH value
means that an EEPROM is present, and EEDET will be
set to 1. A sampled LOW value means that an EE-
PROM is not present, and EEDET will be set to 0. See
the
EEPROM Auto-Detection
section for more details.
If no LED circuit is to be attached to this pin, then a pull
up or pull down resistor must be attached instead in
order to resolve the EEDET setting.
When RST is active, LED1 is an input for NAND tree
testing
.
WARNING: The input signal level of LED1 must be
insured for correct EEPROM detection before the
deassertion of RST.
LED2
LED2
This output is designed to directly drive an LED. By de-
fault, LED2 indicates correct receive polarity on the
10BASE-T interface. This pin can also be programmed
to indicate other network status (see BCR6). The LED2
pin polarity is programmable, but by default it is active
LOW. When the LED2 pin polarity is programmed to
active LOW, the output is an open drain driver. When
the LED2 pin polarity is programmed to active HIGH,
the output is a totem pole driver.
Output
Note:
The LED2 pin is multiplexed with the SRDCLK
pin and the MIIRXFRTGE pins.
When RST is active, LED2 is an input for NAND tree
testing
.
LED3
LED3
This output is designed to directly drive an LED. By de-
fault, LED3 indicates transmit activity on the network.
This pin can also be programmed to indicate other net-
work status (see BCR7). The LED3 pin polarity is pro-
grammable, but by default it is active LOW. When the
LED3 pin polarity is programmed to active LOW, the
output is an open drain driver. When the LED3 pin po-
larity is programmed to active HIGH, the output is a
totem pole driver.
Output
Special attention must be given to the external circuitry
attached to this pin. When this pin is used to drive an
LED while an EEPROM is used in the system, then
buffering is required between the LED3 pin and the
LED circuit. If an LED circuit were directly attached to
this pin, it would create an I
OL
requirement that could
not be met by the serial EEPROM attached to this pin.
If no EEPROM is included in the system design, then
the LED3 signal may be directly connected to an LED
without buffering. For more details regarding LED con-
nection, see the section on
LED Support
.
Note:
The LED3 pin is multiplexed with the EEDO,
SRD, MIIRXFRTGD pins.
When RST is active, LED3 is an input for NAND tree
testing
.
SLEEP
Sleep
When SLEEP is asserted, the Am79C971 controller
performs an internal system reset of the H_RESET
type and then proceeds into a power savings mode. All
Am79C971 controller outputs will be placed in their
normal reset condition. All Am79C971 controller inputs
will be ignored except for the SLEEP pin itself. The sys-
tem must refrain from starting the network operations
of the Am79C971 controller for 0.5 seconds following
the deassertion of the SLEEP pin in order to allow in-
ternal analog circuits to stabilize.
Input
For effects with the Magic Packet
modes, see the
Magic Packet
section.
Both CLK and XTAL1 inputs must have valid clock sig-
nals present in order for the SLEEP command to take
effect.
The SLEEP pin should not be asserted during power
supply ramp up. If it is desired that SLEEP be asserted
at power supply ramp up, then the system must delay
the assertion of SLEEP until three clock cycles after the
completion of hardware reset.
WARNING: The SLEEP pin must not be left uncon-
nected. It should be tied to VDD if the power saving
mode is not used.
Note:
The SLEEP pin is multiplexed with the EAR pin.
When RST is active, SLEEP is an input for NAND tree
testing
.
XTAL1
Crystal Oscillator In
The internal clock generator uses a 20-MHz crystal that
is attached to the pins XTAL1 and XTAL2. The network
data rate is one-half of the crystal frequency. XTAL1
may alternatively be driven using an external 20-MHz
CMOS level clock signal. Refer to the section on
Exter-
nal Crystal Characteristics
for more details. This clock
is always required whether or not the internal
10BASE-T/AUI ports are enabled. If the internal PHY is
Input
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C971KCW | IC LOGIC 16211 24-BIT FET BUS SWITCH -40+85C TSSOP-56 35/TUBE |
| AM79C972BKCW | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C972BKIW | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C972BVCW | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C972 | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C971AKC | 制造商:Advanced Micro Devices 功能描述: |
| AM79C971AVC | 制造商:Advanced Micro Devices 功能描述:10/100 MBPS ETHERNET - Trays |
| AM79C971AVC\\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM79C971AVC\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM79C971AWW WAF | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。