- 您現在的位置：買賣IC網 > PDF目錄375268 > ADUC834BS (ANALOG DEVICES INC) MicroConverter, Dual 16-/24- Bit ADCs with Embedded 62KB FLASH MCU PDF資料下載
參數資料
| 型號： | ADUC834BS |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MicroConverter, Dual 16-/24- Bit ADCs with Embedded 62KB FLASH MCU |
| 中文描述： | 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, PQFP52 |
| 封裝： | 14 X 14 MM, MO-022-AC-1, MQFP-52 |
| 文件頁數： | 26/72頁 |
| 文件大小： | 1451K |
| 代理商： | ADUC834BS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
(12 March 2002) REV.
P
rC
ADuC834
–
26
–
PRELIMINARY TECHNICAL DATA
ADCMODE (ADC Mode Register)
Used to control the operational mode of both ADCs.
SFR Address
Power-On Default Value
Bit Addressable
D1H
00H
No
T able V. ADCMODE SFR Bit Designations
Bit
Name
Description
7
6
5
---
---
ADC0EN
Reserved for Future Use.
Reserved for Future Use.
Primary ADC Enable.
Set
by the user to enable the Primary ADC and place it in the mode selected in MD2-MD0 below
Cleared
by the user to place the Primary ADC in power-down mode.
Auxiliary ADC Enable.
Set
by the user to enable the Auxiliary ADC and place it in the mode selected in MD2-MD0 below
Cleared
by the user to place the Auxiliary ADC in power-down mode.
Reserved for Future Use.
Primary and Auxiliary ADC Mode bits.
T hese bits select the operational mode of the enabled ADC as follows:
MD2
MD1
MD0
0
0
0
ADC Power-Down Mode (Power-On Default)
0
0
1
Idle Mode
In Idle Mode the ADC filter and modulator are held in a reset state
although the modulator clocks are still provided.
0
1
0
Single Conversion Mode
In Single Conversion Mode, a single conversion is performed on the
enabled ADC. On completion of the conversion, the ADC data regis-
ters (ADC0H/M/L and/or ADC1H/L) are updated, the relevant flags
in the ADCST AT SFR are written, and power-down is re-entered with
the MD2–MD0 accordingly being written to 000.
0
1
1
Continuous Conversion
In continuous conversion mode the ADC data registers are regularly
updated at the selected update rate (see SF register)
1
0
0
Internal Zero-Scale Calibration
Internal short automatically connected to the enabled ADC(s)
1
0
1
Internal Full-Scale Calibration
Internal or External V
REF
(as determined by X REF0 and X REF1 bits
in ADC0/1CON) is automatically connected to the ADC input for
this calibration.
1
1
0
System Zero-Scale Calibration
User should connect system zero-scale input to the ADC input pins
as selected by CH1/CH0 and ACH1/ACH0 bits in the ADC0/1CON
register.
1
1
1
System Full-Scale Calibration
User should connect system full-scale input to the ADC input pins as
selected by CH1/CH0 and ACH1/ACH0 bits in the ADC0/1CON
register.
4
ADC1EN
3
2
1
0
---
MD2
MD1
MD0
NOT ES
1. Any change to the MD bits will immediately reset both ADCs. A write to the MD2–0 bits with no change is also treated as a reset. (See exception to this in Note 3
below.)
2. If ADC0CON is written when ADC0EN = 1, or if ADC0EN is changed from 0 to 1, then both ADCs are also immediately reset. In other words, the Primary
ADC is given priority over the Auxiliary ADC and any change requested on the primary ADC is immediately responded to.
3. On the other hand, if ADC1CON is written or if ADC1EN is changed from 0 to 1, only the Auxiliary ADC is reset. For example, if the Primary ADC is continu-
ously converting when the Auxiliary ADC change or enable occurs, the primary ADC continues undisturbed. Rather than allow the Auxiliary ADC to operate with a
phase difference from the primary ADC, the Auxiliary ADC will fall into step with the outputs of the primary ADC. T he result is that the first conversion time
for the Auxiliary ADC will be delayed up to three outputs while the Auxiliary ADC update rate is synchronized to the Primary ADC.
4. Once ADCMODE has been written with a calibration mode, the RDY0/1 bits (ADCST AT ) are immediately reset and the calibration commences. On comple-
tion, the appropriate calibration registers are written, the relevant bits in ADCST AT are written, and the MD2–0 bits are reset to 000 to indicate the ADC is
back in power-down mode.
5. Any calibration request of the Auxiliary ADC while the temperature sensor is selected will fail to complete. Although the RDY 1 bit will be set at the end of
the calibration cycle, no update of the calibration SFRs will take place and the ERR1 bit will be set.
6. Calibrations are performed at maximum SF (see SF SFR) value guaranteeing optimum calibration operation.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUM1310BRWZ | Triple-Channel Digital Isolator with Programmable Default Output |
| ADUM1310BRWZ-RL | Triple-Channel Digital Isolator with Programmable Default Output |
| ADUM3300 | Triple-Channel, Digital Isolators, Enhanced System-Level ESD Reliability |
| ADUM3300ARWZ | Triple-Channel, Digital Isolators, Enhanced System-Level ESD Reliability |
| ADUM3300BRWZ | Triple-Channel, Digital Isolators, Enhanced System-Level ESD Reliability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC834BSZ | 功能描述:IC ADC DUAL16/24BIT W/MCU 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC836 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC836BCP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADUC836BCPZ | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發布緊急采購，3分鐘左右您將得到回復。