參數資料
型號: 28F320D18
廠商: Intel Corp.
英文描述: 1.8 Volt Intel Dual-Plane Flash Memory(1.8 V Intel 雙平面閃速存儲器)
中文描述: 1.8 V的英特爾雙平面閃存(1.8伏英特爾雙平面閃速存儲器)
文件頁數: 40/83頁
文件大小: 836K
代理商: 28F320D18
28F320D18
36
Product Preview
7.2
Flash Software Design Considerations
7.2.1
Conventions and Definitions
Throughout this section references are made to words and phrases which are explained below.
Plane vs. Partition
: Both of these words refer to memory areas within the flash device. A
memory plane is a memory area with its own address range. The main array, status register,
ID/protection register and query are different read planes. These planes may be accessed by
putting the device into the desired mode via commands to the Command User Interface. The
main array plane is split into two physical partitions, with a continuous address range
throughout the two partitions.
Writing a command vs. Writing to the array
: A write is any memory cycle where WE# is
asserted. It is used to get a command or data into the device. A write command is issued to
change the device’s mode. V
PP
does not need to be valid during write command operations.
Writing to the array, or programming, refers to storing memory into the array plane. This is
done with a two-cycle write command, and V
PP
has to be valid during the program operation.
Current Partition
: This is the partition to which commands are currently being written. For
example, if data is being programmed into the bottom partition, this becomes the current
partition and the top partition is referred to as the other partition. If after that, a program
command is issued to the top partition, it then becomes the current partition and the bottom
partition is now the other partition.
Other Partition
: The partition, which is either idle or busy, to which commands are not
currently being written.
Current State
: The state that the Command User Interface is currently in. It can be either the
current partition or the other partition.
Next State
: This will be the state of the flash component after it has received the command to
go into this state.
Setup
: This refers to the current state of the either partition. Setup refers to erase, program,
protection register, block lock/unlock/lock-down and Set Read Configuration Register setup.
Busy
: The other partition is in a busy state when it is in erase, program or protection register
program mode.
Idle
: The other partition is in idle mode when it is not in setup, busy, or erase/program suspend
mode.
LB
= Lock Block
ULB
= Unlock Block
OTP
= One-Time Programmable Protection Register
RCR
= Read Configuration Register
ES
= Erase Suspend
PS
= Program Suspend
BE
= Block Erase
相關PDF資料
PDF描述
28F320J5 5 Volt Intel StrataFlash Memory(5 V 32M位英特爾StrataFlash存儲器)
28F640J5 5 V Intel StrataFlash Memory(5V 64M位英特爾StrataFlash閃速存儲器)
28F400B3 SMART 3 ADVANCED BOOT BLOCK WORD-WIDE
28F400BL-TB 4-MBlT (256K x 16, 512K x 8) LOW-POWER BOOT BLOCK FLASH MEMORY FAMILY
28F400BV-TB 4-MBIT (256K X 16, 512K X 8)SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY
相關代理商/技術參數
參數描述
28F320J3D75 制造商:undefined 功能描述:
28F320J5 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:StrataFlash MEMORY TECHNOLOGY 32 AND 64 MBIT
28F320J5_02 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:5 Volt Intel StrataFlash? Memory
28F320S3 制造商:未知廠家 制造商全稱:未知廠家 功能描述:WORD-WIDE FlashFile MEMORY FAMILY
28F320S5 制造商:未知廠家 制造商全稱:未知廠家 功能描述:WORD-WIDE FlashFile MEMORY FAMILY