- 您現在的位置：買賣IC網 > PDF目錄370035 > 28233-11 (CONEXANT SYSTEMS) ATM Transmitter/Receiver with UTOPIA Interface PDF資料下載
參數資料
| 型號： | 28233-11 |
| 廠商： | CONEXANT SYSTEMS |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | ATM Transmitter/Receiver with UTOPIA Interface |
| 中文描述： | TRANSCEIVER, PQFP160 |
| 封裝： | PLASTIC, MQFP-160 |
| 文件頁數： | 96/161頁 |
| 文件大?。?/td> | 1832K |
| 代理商： | 28233-11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁當前第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
3.0 Registers
CN8223
3.3 Configuration Control Registers
ATM Transmitter/Receiver with UTOPIA Interface
3-10
Conexant
100046C
Disables the payload length check on a per-port basis. This disable controls only the
output of cells to the FIFO interface and does not control the counting of payload
length errors. (Counts are performed collectively, not per port.)
0x29
—
CONFIG_4 (Configuration Control Register 4)
The CONFIG_ 4 register is located at address 0x29 and controls miscellaneous functions.
4
1
Check Input Parity
Enables parity checking at the FIFO port inputs. This bit must be enabled for the
input parity error status bits or interrupts to be active.
3
1
Disable Write
Strobes on Invalid
Cells
Inhibits the receive port FIFO write strobes when a cell is determined to be invalid
for use with generic FIFOs.
2
1
Enable DS1 PRS
Generator
Causes the physical layer data content to be replaced by a quasi-random signal
stream. This stream is used for certain transmission tests in DS1 systems.
1
1
HEC Coverage
Determines the calculation range for the HEC. If this bit is low, the HEC is calculated
over header octets 1
–
4 for ATM cells. If this bit is high, the HEC is calculated over
header octets 2
–
4 for SMDS/802.6 cells.
0
1
Enable HEC Coset
Enables the x
6
+ x
4
+ x
2
+ 1 polynomial to be XOR
’
ed with the calculated HEC prior
to transmission and prior to error detection/correction if HEC is internally
generated. For TAXI mode, enable HEC Coset must be active.
Bit
Field
Size
Name
Description
Bit
Field
Size
Name
Description
15-12
4
Disable CRC
Check-Ports 3
–
0
Disables the payload CRC check on a per-port basis. This disable controls only the
output of cells to the FIFO interface and does not control the counting of payload
CRC errors. (Counts are performed collectively, not per port.)
11-8
4
Disable Length
Check-Ports 3
–
0
7-4
4
Disable Port
Reception-Ports
3
–
0
Disables the output of any received cells on a per-port basis. This disable control is
internally synchronized to cell boundaries so that no partial cells are output on a
port.
3
1
Enable TAXI
Interface
Enables an interface specific to 100 Mbps 4B/5B data transceivers on the parallel
interface port. This interface is detailed in
Section 2.5.1
.
2
1
Delete Idle Cells
Allows the screening of cells matching the receive idle header and mask criteria
from appearing on the outputs of any of the receive ports. When this bit is low, idle
cells are not automatically screened from port output. When this bit is high, idle
cells are screened from output on the receive FIFO port.
1
1
Enable External
Section Trace
Allows the section trace octet (C1) to be inserted externally. When this bit is low, the
C1 octet is generated internally. When this bit is high, the C1 octet is inserted from
the TXOVH input bus.
0
1
STM-1/STS-3c
Pointer
Enables the SS bits to be generated in the AU-4 pointer for STM-1 compatibility.
When this bit is low, an STS-3c H1/H2 pointer is generated by the transmitter (no SS
bits present) and the C2
octet
(1)
has the value 0x13. When this bit is high, an STM-1
AU-4 pointer is generated with the SS bits set to 10.
NOTE(S):
(1)
The C2 octet is the STS Path Signal Label. It is allocated to indicate the content of the STS SPE, including the status of the
mapped payloads.
相關PDF資料 |
PDF描述 |
|---|---|
| 28C010TRPDB-12 | 150 x 32 pixel format, LED Backlight available |
| 28C010TRT1DE-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1DE-20 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1FB-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1FB-20 | 1 Megabit (128K x 8-Bit) EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 282332-2 | 制造商:TE Connectivity 功能描述: |
| 282-333 | 制造商:WAGO Innovative Connections 功能描述:END PLATE RAIL MOUNTED TERMINAL BLOCK 制造商:WAGO 功能描述:END PLATE, RAIL MOUNTED TERMINAL BLOCK 制造商:WAGO Innovative Connections 功能描述:END PLATE, RAIL MOUNTED TERMINAL BLOCK; Series:282; Accessory Type:End Plate; For Use With:Rail Mounted Terminal Blocks; Color:Orange; Mounting Type:DIN Rail ;RoHS Compliant: Yes |
| 2823337 | 功能描述:工業繼電器 ST-REL4-KG120/21-21 RoHS:否 制造商:TE Connectivity / Kilovac 觸點形式:1 Form A (SPST-NO) 觸點電流額定值: 線圈電壓:9 VDC to 36 VDC 線圈電阻:38 Ohms 線圈電流: 切換電壓: 安裝風格:Panel 觸點材料:Silver Palladium |
| 282-334 | 制造商:WAGO Innovative Connections 功能描述:End Plate 2 mm Thick-Color Grey For Use With Rail Mounted Terminal Block 制造商:WAGO 功能描述:GREY END PLATE 制造商:WAGO Innovative Connections 功能描述:END PLATE, 2MM, GREY; Series:-; Accessory Type:End Plate; For Use With:Rail Mounted Terminal Blocks ;RoHS Compliant: Yes |
| 282-334 | 制造商:WAGO Innovative Connections 功能描述:END PLATE 制造商:WAGO 功能描述:END PLATE |
發布緊急采購，3分鐘左右您將得到回復。