- 您現在的位置：買賣IC網 > PDF目錄370035 > 28233-11 (CONEXANT SYSTEMS) ATM Transmitter/Receiver with UTOPIA Interface PDF資料下載
參數資料
| 型號： | 28233-11 |
| 廠商： | CONEXANT SYSTEMS |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | ATM Transmitter/Receiver with UTOPIA Interface |
| 中文描述： | TRANSCEIVER, PQFP160 |
| 封裝： | PLASTIC, MQFP-160 |
| 文件頁數： | 81/161頁 |
| 文件大?。?/td> | 1832K |
| 代理商： | 28233-11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
the second write is not performed, the formatter continues to transmit abort flags
until instructed otherwise.
CN8223
2.0 Functional Description
ATM Transmitter/Receiver with UTOPIA Interface
2.8 FEAC Channel and HDLC Data Link Programming
100046C
Conexant
2-47
The 3-bit field TxBytes[2:0] is functionally split into two parts. The most
significant bit (MSB) indicates to the transmitter circuitry which half of the buffer
to read from next. The two LSBs indicate the stop location, i.e., where the last
message byte is located. When the new controls are latched by the transmitter
circuitry, the processor is interrupted for the next set of controls. Now, the
processor has up to 4-byte intervals (byte transmission time periods) to write a
new set of controls to the control register. Because of a race condition, the ISR
that is processing the transmit interrupt must delay 1.5 byte times before writing a
new control register value. The processor can now write the next block of data to
the next half of the message buffer.
When the end of a message is reached, or in the event of a short message, there
may not be exactly 4 bytes remaining. In this case, the processor writes the
remaining data to the message buffer as usual. The processor now must write the
highest location used to the TxBytes[2:0] field in the data link control register.
Send FCS is set to 1. This causes the FCS to be sent after this last block of data.
When this set of controls is latched, the processor is interrupted. At this time a
new message can be sent, or Send Message can be set to 0 to send idle flags. If a
new message is to be sent immediately, the next half of the transmit buffer can be
written, and the data link control register configured accordingly. This results in
only one idle flag being transmitted between messages. If there is no new
message ready, the processor must write Send Message to 0. If this is not done
within 4 byte intervals, undefined data is transmitted.
2.8.3.2 Aborting a
Message
To abort a message in progress, the controller writes Abort Message to 1 in the
data link control register. The transmitter finishes sending the message byte in
progress, then transmits an abort flag (11111110). After writing the abort signal
to the control register, a second write may follow the next interrupt to cause the
case, the abort flag is followed by one idle flag, and the new message begins. If
2.8.3.3 Transmitter
Interrupts
The transmitter generates an interrupt when it has latched the present set of
controls and is ready for a new set. There are no interrupts during the
transmission of idle flags. Therefore, to start a message from an idle condition,
the processor writes the first half of the buffer and the proper control bits. When
the circuit latches these controls internally, an interrupt is immediately issued for
the next set of control bits. The processor then has up to 4 byte intervals to
respond to the interrupt. The interrupt appears on the DL_INT pin. The
DL_CTRL_STAT register indicates the source of the interrupt but not the cause.
The controller software must know from the message context what response is
required. The interrupt is an active low level, not a pulse. The transmit interrupt is
cleared upon the writing of the DL_CTRL_STAT register. A write operation must
be performed to clear the current interrupt and prevent missing later interrupts.
If the interrupt is a mid-message interrupt, a new data link control word must
be written with TxBytes[2:0] equal to the ending location of the next message
block. The MSB of TxBytes[2:0] informs the transmit circuitry which half of the
buffer to read next.
Interrupts from the HDLC data link transmitter will appear on Transmitter
Interrupt [bit 14] in DL_CTRL_STAT [0x60]. Interrupts must be enabled to
appear on DL_INT by setting Enable HDLC Data Link = 1 in CONFIG_5.
相關PDF資料 |
PDF描述 |
|---|---|
| 28C010TRPDB-12 | 150 x 32 pixel format, LED Backlight available |
| 28C010TRT1DE-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1DE-20 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1FB-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1FB-20 | 1 Megabit (128K x 8-Bit) EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 282332-2 | 制造商:TE Connectivity 功能描述: |
| 282-333 | 制造商:WAGO Innovative Connections 功能描述:END PLATE RAIL MOUNTED TERMINAL BLOCK 制造商:WAGO 功能描述:END PLATE, RAIL MOUNTED TERMINAL BLOCK 制造商:WAGO Innovative Connections 功能描述:END PLATE, RAIL MOUNTED TERMINAL BLOCK; Series:282; Accessory Type:End Plate; For Use With:Rail Mounted Terminal Blocks; Color:Orange; Mounting Type:DIN Rail ;RoHS Compliant: Yes |
| 2823337 | 功能描述:工業繼電器 ST-REL4-KG120/21-21 RoHS:否 制造商:TE Connectivity / Kilovac 觸點形式:1 Form A (SPST-NO) 觸點電流額定值: 線圈電壓:9 VDC to 36 VDC 線圈電阻:38 Ohms 線圈電流: 切換電壓: 安裝風格:Panel 觸點材料:Silver Palladium |
| 282-334 | 制造商:WAGO Innovative Connections 功能描述:End Plate 2 mm Thick-Color Grey For Use With Rail Mounted Terminal Block 制造商:WAGO 功能描述:GREY END PLATE 制造商:WAGO Innovative Connections 功能描述:END PLATE, 2MM, GREY; Series:-; Accessory Type:End Plate; For Use With:Rail Mounted Terminal Blocks ;RoHS Compliant: Yes |
| 282-334 | 制造商:WAGO Innovative Connections 功能描述:END PLATE 制造商:WAGO 功能描述:END PLATE |
發布緊急采購，3分鐘左右您將得到回復。