XRT72L73
THREE CHANNEL, DS3 ATM UNI/CLEAR-CHANNEL FRAMER IC
REV. P1.0.1
á
PRELIMINARY
100
Line Interface Scan register provides DS3UNI framer
chip capability to monitor status of line interface units.
Configuration in this register is connected directly to
the corresponding discrete I/O pins.
Note: These signals drive and scan the line interface
chip XRT73L03.
T
ABLE
116:
L
INE
I
NTERFACE
S
CAN
R
EGISTER
R
EGISTER
115 L
INE
I
NTERFACE
S
CAN
R
EGISTER
H
EX
A
DDRESS
: 0
X
73
B
IT
F
UNCTION
T
YPE
D
EFAULT
D
ESCRIPTION
-O
PERATION
7-3
Unused
RO
0
2
DMO
RO
0
This “Read-Only” bit-field permits the user to determine the current state of
the “DMO” input pin. This input pin can be connected to the “DMO” output
pin of the XRT73L03 device.
0: Indicates that the current state of the “DMO” input pin is “LOW”. If this
input pin is connected to the DMO output of the LIU IC, then this may indi-
cate the occurrence of a fault condition in the “Transmit Output” line.
1: Indicates that the current state of the “DMO” input pin is “High”. If this
input pin is connected to the DMO output of the LIU IC, then this may indi-
cate the occurrence of normal operation in the “Transmit Output” line.
N
OTE
:
For more detailed information on the behavior of the DMO
output pin (from the LIU), please consult the XRT73L03 data sheet.
1
RLOL
RO
0
This “Read-Only” bit-field permits the user to determine the current state of
the “RLOL” input pin. This input pin can be connected to the “RLOL” output
pin of the XRT73L03 device.
0: Indicates that the current state of the “RLOL” input pin is “LOW”. If this
input pin is connected to the “RLOL” output of the LIU IC, then it indicates
that the “Clock Recovery PLL” (within the LIU IC) is locked onto the “incom-
ing” DS3 line signal.
1: Indicates that the current state of the “RLOL” input pin is “HIGH’. If this
input pin is connected to the “RLOL” output of the LIU IC, then it indicates
that the “Clock Recovery PLL” (within the LIU IC) is NOT locked onto the
“incoming” DS3 line signal.
N
OTE
:
For more detailed information on the behavior of the “RLOL” output
pin (from the LIU), please consult the XRT73L03 data sheet.
0
RLOS
RO
0
This “Read-Only” bit-field permits the user to determine the current state of
the “RLOS” input pin. This input pin can (and should be) connected to the
“RLOS” output pin of the XRT73L03 device.
0: Indicates that the current state of the “RLOS” input pin is “LOW”. If this
input pin is connected to the “RLOS” output pin of the LIU IC, then it indi-
cates that the LIU is NOT currently declaring an LOS (Loss of Signal) condi-
tion.
1: Indicates that the current state of the “RLOS” input pin is “HIGH”. If this
input pin is connected to the “RLOS output pin of the LIU IC, then it indicates
that the LIU is currently declaring an LOS condition.
N
OTES
:
1. If this input pin is pulled “High”, then the XRT72L73 will automati-
cally declare an LOS condition. As a consequence, the user should
not treat the the “RLOS” input pin as a General Purpose Input pin.
2. For more detailed on the “LOS Declaration Criteria” for the
XRT73L03 device, please consult the XRT73L03 data sheet.