參數資料
型號: S29CD016G0JFFM012
廠商: Spansion Inc.
英文描述: 32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
中文描述: 32兆位(1米× 32位),16兆位(512k × 32的位),2.5伏,只有突發模式,雙啟動,同步讀/寫閃存與VersatileI內存/輸出
文件頁數: 61/87頁
文件大?。?/td> 792K
代理商: S29CD016G0JFFM012
November 14, 2005 S29CD-G_00_B0
S29CD-G Flash Family
59
P r e l i m i n a r y
Reading Toggle Bits DQ6/DQ2
Refer to
Figure 24
for the following discussion. Whenever the system initially begins reading tog-
gle bit status, it must perform two immediately consecutive reads of DQ7–DQ0 to determine
whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle
bit after the first read. After the second read, the system would compare the new value of the
toggle bit with the first. If the toggle bit is not toggling, the device completed the program or erase
operation. The system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two immediately consecutive read cycles, the system determines that
the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (See
DQ5: Exceeded Timing Limits
on page 60
). If it is, the system should then determine again
whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5
went high. If the toggle bit is no longer toggling, the device successfully completed the program
or erase operation. If it is still toggling, the device did not complete the operation successfully,
and the system must write the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and
DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through suc-
cessive read cycles, determining the status as described in the previous paragraph. Alternatively,
it may choose to perform other system tasks. In this case, the system must start at the beginning
of the algorithm when it returns to determine the status of the operation (top of
Figure 7
).
相關PDF資料
PDF描述
S29CD016G0JFFM100 32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
S29CD016G0JFFM102 32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
S29CD016G0JFFM110 32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
S29CD016G0JFFM112 32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
S29CD016G0JFFM200 32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
相關代理商/技術參數
參數描述
S29CD016G0JFFM100 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
S29CD016G0JFFM102 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
S29CD016G0JFFM110 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
S29CD016G0JFFM112 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O
S29CD016G0JFFM200 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32 Megabit (1M x 32-Bit), 16 Megabit (512K x 32-Bit) 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/ Write Flash Memory with VersatileI/O