參數資料
型號: R5F6418JADFE
元件分類: 微控制器/微處理器
英文描述: MICROCONTROLLER, PQFP176
封裝: 24 X 24 MM, 0.50 MM PITCH, PLASTIC, LQFP-176
文件頁數: 9/128頁
文件大?。?/td> 922K
代理商: R5F6418JADFE
107
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
16.7.2 Compare Match Blocking by TCNT1 Write
All CPU writes to the TCNT1 register will block any compare match that occurs in the next timer clock cycle, even when the
timer is stopped. This feature allows OCR1x to be initialized to the same value as TCNT1 without triggering an interrupt
when the Timer/Counter clock is enabled.
16.7.3 Using the Output Compare Unit
Since writing TCNT1 in any mode of operation will block all compare matches for one timer clock cycle, there are risks
involved when changing TCNT1 when using any of the output compare channels, independent of whether the Timer/Counter
is running or not. If the value written to TCNT1 equals the OCR1x value, the compare match will be missed, resulting in
incorrect waveform generation. Do not write the TCNT1 equal to TOP in PWM modes with variable TOP values. The
compare match for the TOP will be ignored and the counter will continue to 0xFFFF. Similarly, do not write the TCNT1 value
equal to BOTTOM when the counter is downcounting.
The setup of the OC1x should be performed before setting the data direction register for the port pin to output. The easiest
way of setting the OC1x value is to use the force output compare (FOC1x) strobe bits in normal mode. The OC1x register
keeps its value even when changing between waveform generation modes.
Be aware that the COM1x1:0 bits are not double buffered together with the compare value. Changing the COM1x1:0 bits will
take effect immediately.
16.8
Compare Match Output Unit
The compare output mode (COM1x1:0) bits have two functions. The waveform generator uses the COM1x1:0 bits for
defining the output compare (OC1x) state at the next compare match. Secondly the COM1x1:0 bits control the OC1x pin
output source. Figure 16-5 shows a simplified schematic of the logic affected by the COM1x1:0 bit setting. The I/O registers,
I/O bits, and I/O pins in the figure are shown in bold. Only the parts of the general I/O port control registers (DDR and PORT)
that are affected by the COM1x1:0 bits are shown. When referring to the OC1x state, the reference is for the internal OC1x
register, not the OC1x pin. If a system reset occur, the OC1x register is reset to “0”.
Figure 16-5. Compare Match Output Unit, Schematic
DA
T
A
BUS
0
1
Q
D
COMnx1
COMnx0
FOCn
OCnx
Waveform
Generator
Q
D
PORT
Q
D
DDR
OCnx
Pin
clkI/O
相關PDF資料
PDF描述
R5F64200LFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F64200JFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F64201JFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F64201KFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F6420FLFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
R5F6418JANFD 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F6418JANFE 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F6418JANFE_12 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F6418JAPFD 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F6418JAPFE 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU