參數資料
型號： R5F6418JADFE
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP176
封裝： 24 X 24 MM, 0.50 MM PITCH, PLASTIC, LQFP-176
文件頁數： 83/128頁
文件大小： 922K
代理商： R5F6418JADFE
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
58
12.4
Register Description
12.4.1 Moving Interrupts Between Application and Boot Space, Atmel ATmega88PA, ATmega168PA
The MCU control register controls the placement of the interrupt vector table.
MCUCR – MCU control register
Note:
BODS and BODSE only available for picoPower devices ATmega48PA/88PA/168PA
Bit 1 – IVSEL: Interrupt Vector Select
When the IVSEL bit is cleared (zero), the interrupt vectors are placed at the start of the flash memory. When this bit is set
(one), the interrupt vectors are moved to the beginning of the boot loader section of the flash. The actual address of the start
of the boot flash section is determined by the BOOTSZ Fuses. Refer to the
changes of interrupt vector tables, a special write procedure must be followed to change the IVSEL bit:
a.
Write the interrupt vector change enable (IVCE) bit to one.
b.
Within four cycles, write the desired value to IVSEL while writing a zero to IVCE.
Interrupts will automatically be disabled while this sequence is executed. Interrupts are disabled in the cycle IVCE is set, and
they remain disabled until after the instruction following the write to IVSEL. If IVSEL is not written, interrupts remain disabled
for four cycles. The I-bit in the status register is unaffected by the automatic disabling.
Note:
If interrupt vectors are placed in the boot loader section and boot lock bit BLB02 is programmed, interrupts are
disabled while executing from the application section. If interrupt vectors are placed in the application section
and boot lock bit BLB12 is programed, interrupts are disabled while executing from the boot loader section.
on boot lock bits.
Bit 0 – IVCE: Interrupt Vector Change Enable
The IVCE bit must be written to logic one to enable change of the IVSEL bit. IVCE is cleared by hardware four cycles after it
is written or when IVSEL is written. Setting the IVCE bit will disable interrupts, as explained in the IVSEL description above.
See code example below.
Bit
7
6
5
43210
–
BODS(1) BODSE(1)
PUD
–
IVSEL
IVCE
MCUCR
Read/Write
R
R/W
R
R/W
Initial Value
0
00000
Assembly Code Example
Move_interrupts:
; Enable change of Interrupt Vectors
ldi
r16, (1<<IVCE)
out
MCUCR, r16
; Move interrupts to Boot Flash section
ldi
r16, (1<<IVSEL)
out
MCUCR, r16
ret
C Code Example
void
Move_interrupts(void)
{
/* Enable change of Interrupt Vectors */
MCUCR = (1<<IVCE);
/* Move interrupts to Boot Flash section */
MCUCR = (1<<IVSEL);
}
相關PDF資料
PDF描述
R5F64200LFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F64200JFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F64201JFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F64201KFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
R5F6420FLFB 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
R5F6418JANFD 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F6418JANFE 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F6418JANFE_12 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F6418JAPFD 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
R5F6418JAPFE 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*