- 您現在的位置：買賣IC網 > PDF目錄69315 > R5F6418JADFE MICROCONTROLLER, PQFP176 PDF資料下載
參數資料
| 型號： | R5F6418JADFE |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, PQFP176 |
| 封裝： | 24 X 24 MM, 0.50 MM PITCH, PLASTIC, LQFP-176 |
| 文件頁數： | 43/128頁 |
| 文件大?。?/td> | 922K |
| 代理商： | R5F6418JADFE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
21
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
Bit 3 – EERIE: EEPROM Ready Interrupt Enable
Writing EERIE to one enables the EEPROM ready interrupt if the I bit in SREG is set. Writing EERIE to zero disables the
interrupt. The EEPROM ready interrupt generates a constant interrupt when EEPE is cleared. The interrupt will not be
generated during EEPROM write or SPM.
Bit 2 – EEMPE: EEPROM Master Write Enable
The EEMPE bit determines whether setting EEPE to one causes the EEPROM to be written. When EEMPE is set, setting
EEPE within four clock cycles will write data to the EEPROM at the selected address If EEMPE is zero, setting EEPE will
have no effect. When EEMPE has been written to one by software, hardware clears the bit to zero after four clock cycles.
See the description of the EEPE bit for an EEPROM write procedure.
Bit 1 – EEPE: EEPROM Write Enable
The EEPROM write enable signal EEPE is the write strobe to the EEPROM. When address and data are correctly set up,
the EEPE bit must be written to one to write the value into the EEPROM. The EEMPE bit must be written to one before a
logical one is written to EEPE, otherwise no EEPROM write takes place. The following procedure should be followed when
writing the EEPROM (the order of steps 3 and 4 is not essential):
1.
Wait until EEPE becomes zero.
2.
Wait until SELFPRGEN in SPMCSR becomes zero.
3.
Write new EEPROM address to EEAR (optional).
4.
Write new EEPROM data to EEDR (optional).
5.
Write a logical one to the EEMPE bit while writing a zero to EEPE in EECR.
6.
Within four clock cycles after setting EEMPE, write a logical one to EEPE.
The EEPROM can not be programmed during a CPU write to the flash memory. The software must check that the flash
programming is completed before initiating a new EEPROM write. Step 2 is only relevant if the software contains a boot
loader allowing the CPU to program the flash. If the flash is never being updated by the CPU, step 2 can be omitted. See
Section 27. “Boot Loader Support – Read-While-Write Self-Programming” on page 237 for details about Boot programming.
Caution:
An interrupt between step 5 and step 6 will make the write cycle fail, since the EEPROM master write enable
will time-out. If an interrupt routine accessing the EEPROM is interrupting another EEPROM access, the EEAR
or EEDR register will be modified, causing the interrupted EEPROM access to fail. It is recommended to have
the global interrupt flag cleared during all the steps to avoid these problems.
When the write access time has elapsed, the EEPE bit is cleared by hardware. The user software can poll this bit and wait
for a zero before writing the next byte. When EEPE has been set, the CPU is halted for two cycles before the next instruction
is executed.
Bit 0 – EERE: EEPROM Read Enable
The EEPROM read enable signal EERE is the read strobe to the EEPROM. When the correct address is set up in the EEAR
register, the EERE bit must be written to a logic one to trigger the EEPROM read. The EEPROM read access takes one
instruction, and the requested data is available immediately. When the EEPROM is read, the CPU is halted for four cycles
before the next instruction is executed.
The user should poll the EEPE bit before starting the read operation. If a write operation is in progress, it is neither possible
to read the EEPROM, nor to change the EEAR register.
Table 8-1.
EEPROM Mode Bits
EEPM1
EEPM0
Programming Time
Operation
0
3.4ms
Erase and write in one operation (atomic operation)
0
1
1.8ms
Erase only
1
0
1.8ms
Write only
1
–
Reserved for future use
相關PDF資料 |
PDF描述 |
|---|---|
| R5F64200LFB | 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100 |
| R5F64200JFB | 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100 |
| R5F64201JFB | 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100 |
| R5F64201KFB | 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100 |
| R5F6420FLFB | 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R5F6418JANFD | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F6418JANFE | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F6418JANFE_12 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F6418JAPFD | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F6418JAPFE | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
發布緊急采購，3分鐘左右您將得到回復。