- 您現在的位置：買賣IC網 > PDF目錄369993 > pentium III CPU (Intel Corp.) Pentium III Processor for the SC242 at 450MHz to 1.0GHz(SC242工作頻率450MHZ到1GHZ奔III處理器) PDF資料下載
參數資料
| 型號： | pentium III CPU |
| 廠商： | Intel Corp. |
| 英文描述： | Pentium III Processor for the SC242 at 450MHz to 1.0GHz(SC242工作頻率450MHZ到1GHZ奔III處理器) |
| 中文描述： | 奔騰III處理器在450MHz至1.0GHz的（SC242工作頻率至450MHz到1GHz的奔三處理器的SC242） |
| 文件頁數： | 22/102頁 |
| 文件大?。?/td> | 920K |
| 代理商： | PENTIUM III CPU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
22
Datasheet
Pentium
III Processor for the SC242 at 450 MHz to 1.0 GHz
2.8.2
System Bus Frequency Select Signal (BSEL0)
The BSEL[1:0] signals (BSEL0 is also known as 100/66#) are used to select the system bus
frequency for the Pentium
III
processor(s).
Table 5
defines the possible combinations of the signals
and the frequency associated with each combination. The frequency is determined by the
processor(s), and frequency synthesizer. All system bus agents must operate at the same core and
system bus frequency in a 2-way MP Pentium
III
processor configuration. In a 2-way MP system
design, the BSEL[1:0] signals must be connected to the BSEL[1:0] pins of both processors. The
Pentium
III
processor operates at either a 100 MHz or 133 MHz system bus frequency, but not
both. 66 MHz system bus operation is not supported.
For systems that support only a 100 MHz system bus clock, resistors on the processor cartridge
will tie the BSEL1 signal to ground (as shown in
Figure 4
). This signal can either be left as a no
connect or tied to ground as shown below. The BSEL0 should be pulled up to 3.3 V with a 220
resistor, and provided as a frequency driver to the clock driver/synthesizer.
On baseboards which support operation at either 100 or 133 MHz, the BSEL[1:0] signals should be
pulled up to 3.3 V with a 220
resistor (as shown in
Figure 5
and
Figure 6
) and BSEL1 is
provided as a frequency selection signal to the clock driver/synthesizer. The BSEL0 signal can also
be incorporated into system shutdown logic on the baseboard (thus forcing the system to shutdown
as long as the BSEL0 signal is low).
Figure 4
shows this routing example with a 100 MHz
Pentium
III
processor.
Figure 5
shows the same routing example with a 133 MHz Pentium
III
processor.
Table 5. Frequency Select Truth Table for BSEL[1:0]
BSEL1
BSEL0
Frequency
0
0
66MHz (unsupported)
0
1
100 MHz
1
0
Reserved
1
1
133MHz
Figure 4. BSEL[1:0] Example for a 100 MHz System Design (100 MHz Processor Installed)
Processor
Core
GND
GND
BSEL1
0
0
1
Κ
3.3
Κ
100/66#
CK100
GND
3.3V
220
BSEL0
S
C
2
4
2
Intel
Pentium
III Processor
相關PDF資料 |
PDF描述 |
|---|---|
| pentium III processor | 32 bit Processor Mobile Module(32 位帶移動模塊處理器) |
| Pentium OverDrive Processor | Pentium OverDrive Processor With MMX Technology For Pentium Processor-Based System(帶MMX技術奔騰超速轉動處理器) |
| pentium pro processor | Pentium Pro Processor with 1MB L2 Cache at 200MHZ(1兆比特L2高速緩存頻率200兆赫茲處理器) |
| pentium processor with MMX | 32-bit processor with MMX technology(32位帶MMX技術處理器) |
| pentium processor | 32 Bit Processor With MMX And Mobile Module(32位帶移動模塊和MMX技術CPU) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P-ENV568K3G3 | 制造商:Panasonic Industrial Company 功能描述:TUNER |
| PEO14012 | 制造商:TE Connectivity 功能描述:RELAY SPCO 12VDC |
| PEO14024 | 制造商:TE Connectivity 功能描述:RELAY SPCO 24VDC |
| PEO96742 | 制造商:Delphi Corporation 功能描述:ASM TERM |
| PEOODO3A | 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint |
發布緊急采購，3分鐘左右您將得到回復。