- 您現在的位置：買賣IC網 > PDF目錄367733 > P83CL882 (NXP Semiconductors N.V.) 80C51 Ultra Low Power ULP telephony controller PDF資料下載
參數資料
| 型號： | P83CL882 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 80C51 Ultra Low Power ULP telephony controller |
| 中文描述： | 80C51的超低功耗無鉛汽油電話控制器 |
| 文件頁數： | 60/88頁 |
| 文件大小： | 328K |
| 代理商： | P83CL882 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
2001 Jun 19
60
Philips Semiconductors
Product specification
80C51 Ultra Low Power (ULP) telephony controller
P83CL882
6.9.5
D
ATA TRANSMISSION
DatatransmissionisenabledifbitMTENinregisterMCON
is set to a logic 1. If MTEN is a logic 0, data transmission
is disabled and MOUT[2:0] is set to ‘111’ to zero the
currents in the resistive DAC. Setting MTEN to a logic 1
sets MOUT[2:0] to the idle value ‘100’. This results in
a value close to
1
/
2
V
DD
on the output signal of the external
DAC. Transmission is started by loading the first byte into
register MBUF. All bytes are transmitted starting with the
MSB.
A message is transferred in a block of 3 or more bytes, the
first two bytes being the programmed Manchester
preamble pattern. In order to insert the preamble pattern,
the first two bytes AAH and AxH (with ‘x’ being the
MPR3 to MPR0 value programmed in the receiver MSK
modem) have to be written to MBUF by software.
After this, the first byte of the message is written to MBUF.
As soon as MBUF is ready to accept new input, signal MTI
is set.
The minimum time between two MTI interrupts is:
8
If no new byte is written to MBUF at the end of a byte
transmission, the modem transmitter stops transmission
and MOUT[2:0] is set to the idle state ‘100’.
MTI must be cleared explicitly. If MTEN is reset during
transmission, the transmitter will finish the transmission of
the current byte and then will set MOUT[2:0] to the off
state ‘111’. No interrupt on MTI will be generated at the
end of the transmission.
t
min
baud rate
=
handbook, full pagewidth
MGK229
MOUT
80C51
access
set
MTEN
clear
MTI
write
MBUF
AAH
write
MBUF
ADH
write
MBUF
AAH
write
MBUF
55H
write
MBUF
55H
MTI
TX_MUTE
data ADH
data AAH
data AAH
data 55H
data 55H
Fig.28 Data transmission timing diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| P83CL883T | TELX microcontrollers for CT0 handset/basestation applications |
| P83CL884T | TELX microcontrollers for CT0 handset/basestation applications |
| P87CL883T | TELX microcontrollers for CT0 handset/basestation applications |
| P87CL884T | TELX microcontrollers for CT0 handset/basestation applications |
| P8503BMG | N-Channel Logic Level Enhancement Mode Field Effect Transistor (Preliminary) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P83CL882T/001 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 Ultra Low Power ULP telephony controller |
| P83CL883T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:TELX microcontrollers for CT0 handset/basestation applications |
| P83CL883T/XXX | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|SOP|28PIN|PLASTIC |
| P83CL884T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:TELX microcontrollers for CT0 handset/basestation applications |
| P83CL884T/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。