參數資料
型號： LQ80221
英文描述： LAN Transceiver
中文描述： 網絡收發器
文件頁數： 84/91頁
文件大?。?/td> 907K
代理商： LQ80221
80220/80221
MD400159/E
84
Page 7, Pin Configuration continued:
- Pin Name PLED5 Description, all references to Transmit have been changed to Receive.
- Pin Name PLED4 Description, all references to Receive have been changed to Transmit.
- New reference to Pin #30 including Pin name, I/O and Description, has been added.
Page 8, Pin Description continued:
- 80 PQFP reference to Pin #30 has been deleted.
Page 9, Figure 1. 80220/80221 Block Diagram:
- Reference to RPTR
[1]
has been added.
Page 12, Table 1 80220 vs. 80221:
- Repeater Mode Pin has been added.
Page 13, Section 3.3.4 FBI - 100 Mbps:
- Paragraph 2 copy, ...RXD4, (4) CRS is asserted as long as the device is in the Link.... has been added.
Page 19, Section 3.9.4 TP Squelch, 10 Mbps:
- Reference to 75-250 nS has been changed to 50-250 nS.
Page 24, Section 3.13.9 Link Indication:
- Copy change, copy has been changed to...The PLED3 output is open drain with resistor pullup and can drive
an LED from VCC; The PLED0 output has both pullup and pulldown driver transistors in addition to a weak pullup
resistor, so it can drive an LED from either VCC or GND. Both PLED3 and PLED0 can also drive another digital
input. Refer...
Page 25, Section 3.15.2 10 Mbps:
- Copy change, copy has been changed to...If either 3 consecutive link pulses or one SOI pulse indicates incorrect
polarity on the TP receive input, ...
Section 3.16.3 Full Duplex Indication:
- Copy change, copy has been changed to...The PLED1 output has both pullup and pulldown driver transistors and
a weak pullup resistor, ...
Section 3.17.2 10/100 Mbps Indication:
- Copy change, copy has been changed to...The PLED0 output has both pullup and pulldown driver transistors
and a weak pullup resistor, ...
Section 3.18.1 Internal CRS Loopback:
- Copy change, copy has been changed to... in Link Fail State, and when the transmit disable bit is set in the MI
serial port Configuration 1 register. In 10 Mbps mode, ...
Page 26, Section 3.18.2 Diagnostic Loopback:
- Copy addition, copy has been changed to...do not change. Diagnostic loopback mode can not be enabled
when the FBI interface is selected.
Section 3.23 LED DRIVERS:
- First paragraph has changed to ...The PLED[5:2] outputs are open drain with a pullup resistor and can drive
LED's tied to VCC. The PLED[1:0] outputs have both pullup and pulldown driver transistors with a pullup resistor,
so PLED[1:0] can drive LED's tied to either VCC or GND.
Page 27, Table 5. LED Normal Function Definition:
- Columns PLED5 and PLED4 references to XMT and RCV have been switched, XMT is now RCV etc.
- Section 3.25 Repeater Mode has been added.
- Reference to Sections 3.25 have been changed to 3.26.
Page 28, Reference to Sections 3.25 have been changed to 3.26.
Table 7. MI Register Bit Type Definition:
- R/WS C Column, Write Cycle, Clears Itself After Operation Completed is now under Column Read Cycle.
Revision History
相關PDF資料
PDF描述
LQT100X Peripheral IC
LQT1KX Peripheral IC
LQT50X3 Peripheral IC
LQT60X3 Peripheral IC
LQV3M2768-3CGR Peripheral IC
相關代理商/技術參數
參數描述
LQ821 制造商:POLYFET 制造商全稱:Polyfet RF Devices 功能描述:SILICON GATE ENHANCEMENT MODE RF POWER LDMOS TRANSISTOR
LQ9D161 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:DEVICE SPECIFICATION FOR TFT-LCD module
LQ9D340 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Color TFT-LCD Module for Measuring instruments/Banking terminals
LQA03TC600 功能描述:整流器 Q-Series 600V 3A Ultra Low Qrr RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
LQA05TC600 功能描述:整流器 Q-Series 600V 5A Ultra Low Qrr RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*