- 您現在的位置：買賣IC網 > PDF目錄369830 > LQ80221 LAN Transceiver PDF資料下載
參數資料
| 型號： | LQ80221 |
| 英文描述： | LAN Transceiver |
| 中文描述： | 網絡收發器 |
| 文件頁數： | 49/91頁 |
| 文件大?。?/td> | 907K |
| 代理商： | LQ80221 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁
80220/80221
4-49
MD400159/E
Table 21. TP Transformer Specification
Parameter
Specification
Transmit
2:1 CT
350
0.05-0.15
15
0.4
Receive
1:1
350
0.0-0.2
15
0.4
Turns Ratio
Inductance, (
μ
H Min)
Leakage Inductance, (
μ
H)
Capacitance (pF Max)
DC Resistance (Ohms Max)
Table 22. TP Transformer Sources
Vendor
Valor
NanoPulse
PCA
Belfuse
Part Number
ST6129
NPI 6254-30
EPF 8025G
S558-5999-96
or S558-5999-98
H1038/H1039
PT 163042
Pulse Engineering
YCL
5.4 TP TRANSMIT OUTPUT CURRENT SET
The TPO
±
output current evel s set by an external resistor
tied between REXT and GND. This output current is
determined by the following equation where R is the value
of REXT:
I
out
= (10K/R)
I
ref
Where I
ref
= 20 mA (100 Mbps, UTP)
= 16.3 mA (100 Mbps, STP)
= 50 mA (10 Mbps, UTP)
= 40.8 mA (10 Mbps, STP)
For 100 Ohm UTP (unshielded twisted pair cable), REXT
should be typically set to 10K Ohms and REXT should be
a 1% resistor n order to meet IEEE 802.3 specified evels.
Once REXT is set for the 100 Mbps and UTP modes as
shown by the equation above, I
is then automatically
changed inside the device when the 10 Mbps mode or
UTP120/STP150 modes are selected.
Keep REXT close to the REXT and GND pins as possible
in order to reduce noise pickup into the transmitter.
Since the TP output is a current source, capacitive and
inductive loading can reduce the output voltage level from
the ideal. Thus, in actual application, it might be neces-
sary to adjust the value of the output current to compen-
sate for external loading. One way to adjust the TP output
level is to change the value of the external resistor tied to
REXT. A better way to adjust the TP output level is to use
the transmit evel adjust register bits accessed through the
MI serial port. These four bits can adjust the output level
by -14% to +16% in 2% steps as described in Table 3.
5.5 CABLE SELECTION
The 80220/80221 can drive two different cable types: (1)
100 Ohm unshielded twisted pair, Category 5, or (2) 150
Ohm shielded twisted pair.
The 80220/80221 must be properly configured for the type
of cable in order to meet the return loss specifications in
IEEE 802.3. This configuration requires setting a bit n the
serial port and setting the value of some external resistors,
as described in Table 23. The Cable Type Select bit in
Table 23 is a bit in the MI serial port Configuration 1
register that sets the output current evel for the cable type.
R
in Table 23 is the value of the termination resistors
needed to meet the level and return loss requirements.
The value for R
on the TPO
±
outputs is for the two
external termination resistors connected between VCC to
TPO
±
; the value for R
on the TPI
±
nputs s for the sum
of the four series resistors across TPI
±
, as shown in
Figures 11-13. These resistors should be 1% tolerance.
Also note that some output level adjustment may be
necessary due to parasitics as described in the TP Output
Current section.
Table 23. Cable Configuration
Cable Type
Cable Type
R
TERM
(Ohms)
Select Bit
(16.7)
UTP
STP
TPO
±
200
300
TPI
±
100
150
100 Ohm UTP, Cat. 5
150 Ohm STP
5.6 TRANSMITTER DROOP
The IEEE 802.3 specification has a transmit output droop
requirement for 100BaseTX. Since the 80220/80221 TP
output is a current source, it has no perceptible droop by
itself. However, the inductance of the transformer added
to the device transmitter output as shown n Figures 11-13
will cause droop to appear at the transmit interface to the
TP wire. If the transformer connected to the 80220/80221
outputs meets the requirements in Table 21, the transmit
interface to the TP cable will meet the IEEE 802.3 droop
requirements.
*
相關PDF資料 |
PDF描述 |
|---|---|
| LQT100X | Peripheral IC |
| LQT1KX | Peripheral IC |
| LQT50X3 | Peripheral IC |
| LQT60X3 | Peripheral IC |
| LQV3M2768-3CGR | Peripheral IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LQ821 | 制造商:POLYFET 制造商全稱:Polyfet RF Devices 功能描述:SILICON GATE ENHANCEMENT MODE RF POWER LDMOS TRANSISTOR |
| LQ9D161 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:DEVICE SPECIFICATION FOR TFT-LCD module |
| LQ9D340 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Color TFT-LCD Module for Measuring instruments/Banking terminals |
| LQA03TC600 | 功能描述:整流器 Q-Series 600V 3A Ultra Low Qrr RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| LQA05TC600 | 功能描述:整流器 Q-Series 600V 5A Ultra Low Qrr RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。