- 您現在的位置：買賣IC網 > PDF目錄369830 > LQ80221 LAN Transceiver PDF資料下載
參數資料
| 型號： | LQ80221 |
| 英文描述： | LAN Transceiver |
| 中文描述： | 網絡收發器 |
| 文件頁數： | 25/91頁 |
| 文件大?。?/td> | 907K |
| 代理商： | LQ80221 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁
80220/80221
4-25
MD400159/E
3.16 FULL DUPLEX MODE
3.16.1 100 Mbps
Full Duplex mode allows transmission and reception to
occur simultaneously. When Full Duplex mode s enabled,
collision is disabled and internal TX_EN to CRS loopback
is disabled.
The device can be either forced into Half or Full Duplex
mode, or the device can detect either Half or Full Duplex
capability from a remote device and automatically place
itself in the correct mode.
The device can be forced into the Full or Half Duplex
modes by setting the duplex bit n the MI serial port Control
register.
The device can automatically configure itself for Full or
Half Duplex modes by using the AutoNegotiation algo-
rithm to advertise and detect Full and Half Duplex capabili-
ties to and from a remote terminal. All of this is described
in detail in the Link Integrity and AutoNegotiation section.
3.16.2 10 Mbps
Full Duplex in 10 Mbps mode is identical to the 100 Mbps
mode.
3.16.3 Full Duplex Indication
Full Duplex detection can be monitored hrough he duplex
bit n the MI serial port Status Output register, or t can also
be programmed to appear on the PLED1 pin by appropri-
ately setting the programmable LED output select bits in
the MI serial port Configuration 2 register as described in
Table 5. When the PLED1 pin is programmed to be a Full
Duplex detect output, this pin is asserted low when the
device s configured or Full Duplex operation. The PLED1
output has both pullup and pulldown driver transistors and
a weak pullup resistor, so it can drive an LED from either
VCC or GND and can also drive a digital input.
3.17 100/10 MBPS SELECTION
3.17.1 General
The device can be forced into either the 100 or 10 Mbps
mode, or the device also can detect 100 or 10 Mbps
capability from a remote device and automatically place
itself in the correct mode.
The device can be forced into either the 100 or 10 Mbps
mode by setting the speed select bit in the MI serial port
Control register.
The device can automatically configure tself for 100 or 10
Mbps mode by using the AutoNegotiation algorithm to
advertise and detect 100 and 10 Mbps capabilities to and
from a remote terminal. All of this is described in detail in
the Link Integrity & AutoNegotiation section.
3.17.2 10/100 Mbps Indication
The device speed (100/10 Mbps) can be determined
through the speed bit in the MI serial port Status Output
register, or it can also be programmed to appear on the
PLED0 pin by setting the programmable LED output
select bits in the MI serial port Configuration 2 register.
When the PLED0 pin is programmed to be speed detect
output, this pin is asserted low when the device is config-
ured for 100 Mbps operation. The PLED0 output has both
pullup and pulldown driver transistors and a weak pullup
resistor, so it can drive an LED from either VCC or GND
and can also drive a digital input.
3.18 LOOPBACK
3.18.1 Internal CRS Loopback
TX_EN is internally looped back onto CRS during every
transmit packet. This internal CRS loopback is disabled
during collision, n Full Duplex mode, n Link Fail State, and
when the transmit disable bit is set in the MI serial port
Configuration 1 register. In 10 Mbps mode, internal CRS
loopback is also disabled when jabber is detected.
The internal CRS loopback can be disabled by setting the
TX_EN to CRS loopback disable bit in the MI serial port
Configuration 1 register. When this bit is set, TX_EN is no
longer looped back to CRS.
相關PDF資料 |
PDF描述 |
|---|---|
| LQT100X | Peripheral IC |
| LQT1KX | Peripheral IC |
| LQT50X3 | Peripheral IC |
| LQT60X3 | Peripheral IC |
| LQV3M2768-3CGR | Peripheral IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LQ821 | 制造商:POLYFET 制造商全稱:Polyfet RF Devices 功能描述:SILICON GATE ENHANCEMENT MODE RF POWER LDMOS TRANSISTOR |
| LQ9D161 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:DEVICE SPECIFICATION FOR TFT-LCD module |
| LQ9D340 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Color TFT-LCD Module for Measuring instruments/Banking terminals |
| LQA03TC600 | 功能描述:整流器 Q-Series 600V 3A Ultra Low Qrr RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| LQA05TC600 | 功能描述:整流器 Q-Series 600V 5A Ultra Low Qrr RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。