亚洲永久无码中文字幕,欧美自拍三级片在线观看,狠狠任你日线观看免费

您好，
買賣IC網歡迎您。
請登錄
免費注冊

您現在的位置：買賣IC網 > PDF目錄67761 > M32185F4VFP 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144 PDF資料下載

型號：	M32185F4VFP
元件分類：	微控制器/微處理器
英文描述：	32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
封裝：	20 X 20 MM, 0.50 MM PITCH, PLASTIC, LQFP-144
文件頁數：	354/1032頁
文件大?。?/td>	5750K
代理商：	M32185F4VFP

10.4 TIO (Input/Output-Related 16-Bit Timer)

MULTIJUNCTION TIMERS

32185/32186 Group Hardware Manual

Rev.1.10 REJ09B0235-0110 May 15, 07

10.4.2 Outline of Each Mode of TIO

Each mode of TIO is outlined below. For each TIO channel, only one of the following modes can be selected.

(1) Measure clear/free-run input modes

In measure clear/free-run input modes, the timer is used to measure a duration of time from when the

counter starts counting until when an external capture signal is entered.And also it is possible to generate

both an interrupt requested by underflow at the counter or execution of measurement operation and a DMA

transfer request (for only the TIO8 and TIO9) upon underflow of the counter.

After the timer is enabled (by writing to the enable bit in software), the counter starts counting down synchro-

nously with the count clock. When a capture signal is entered from an external device, the counter value at

that point in time is written into a register called the “measure register.”

In measure clear input mode, the counter value is initialized to H’FFFF upon capture, from which the counter

starts counting down again. The counter returns to H’FFFF upon underflow, from which it starts counting

down.Furthermore when it underflows goes back to H’FFFF and continues down counting.

In measure free-run input mode, the counter continues counting down even after capture. The counter

returns to H’FFFF upon underflow, from which it starts counting down again.

To stop the counter, disable count by writing to the enable bit in software.

(2) Noise processing input mode

In noise processing input mode, the timer is used to detect that the input signal remained in the same state

for over a predetermined time.

In noise processing input mode, a "H" or "L" level on external input activates the counter and if the input signal

remains in the same state for over a predetermined time before the counter underflows, the counter generates

an interrupt request before stopping. If the valid-level signal being applied turns to an invalid level before the

counter underflows, the counter temporarily stops counting and at the next cycle when a valid-level signal is

entered again, the counter is reloaded with the value that " the reload register -1" and restarts counting.

The timer stops at the same time the counter underflows or count is disabled by writing to the enable bit.

Furthermore, it is possible to generate an interrupt request and a DMA transfer request (for only the TIO8

and TIO9) upon underflow of the counter.

(3) PWM output mode (without correction function)

In PWM output mode, the timer uses two reload registers to generate a waveform with a given duty cycle.

When the timer is enabled (by writing to the enable bit in software or by external input) after setting the initial

values in the reload 0 and reload 1 registers, the counter is loaded with the value that “ the reload 0 register

-1” and starts counting down synchronously with the count clock at the next cycle.The next cycle after the

first time the counter underflows, it is loaded with the value that “ the reload 1 register -1” and continues

counting. Thereafter, the counter is loaded with the reload 0 and reload 1 register values alternately each

time an underflow occurs.The effective counter value is “reload 0 register set value +1” or “reload 1 register

set value +1.”

The timer stops at the same time count is disabled by writing to the enable bit (and not in synchronism with

PWM output period).

The F/F output waveform in PWM output mode is inverted (F/F output level changes from "L" to "H" or vice

versa), when the counter starts counting and each time it underflows.

Furthermore, it is possible to generate an interrupt request at even-numbered occurrences of underflow after the

counter is enabled and a DMA transfer request (for only the TIO8 and TIO9) every time the counter underflows.

In addition PWM output mode of TIO does not have function of correction.

相關PDF資料	PDF描述
M32185F4VFP	32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
M34283G2GP	4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20
M34283G2-XXXGP	4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20
M34502E4FP	4-BIT, OTPROM, MICROCONTROLLER, PDSO24
M34502M4-XXXFP	4-BIT, MROM, MICROCONTROLLER, PDSO24

相關代理商/技術參數	參數描述
M32186F8VFP	制造商:Renesas Electronics Corporation 功能描述:
M3219	功能描述:電纜固定件和配件 LTCG PG-16 BLACK With 3173 NUT RoHS:否制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M32192F8TFP#U0	制造商:Renesas Electronics Corporation 功能描述:MCU 32-bit M32R RISC 1024KB Flash 3.3V/5V 144-Pin LQFP
M32192F8VFP	制造商:Renesas Electronics Corporation 功能描述:
M321-SERIES	制造商:未知廠家制造商全稱:未知廠家功能描述:Peripheral IC

發布緊急采購，3分鐘左右您將得到回復。

(若只采購一條型號，填寫一行即可)

*型號	*數量	廠商	批號	封裝

采購需求

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

我的聯系方式

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價