- 您現在的位置：買賣IC網 > PDF目錄369517 > BT849A Single-Chip Video Capture for PCI PDF資料下載
參數資料
| 型號： | BT849A |
| 英文描述： | Single-Chip Video Capture for PCI |
| 中文描述： | 單芯片的PCI視頻捕捉 |
| 文件頁數： | 66/141頁 |
| 文件大?。?/td> | 1149K |
| 代理商： | BT849A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁
Bt848/848A/849A
Single-Chip Video Capture for PCI
Brooktree
56
F
UNCTIONAL
D
ESCRIPTION
DMA Controller
L848A_A
Executing Instructions
Once the DMA controller has achieved synchronization between the FIFO and the
RISC program, it proceeds with executing the RISC instructions. The data in the
FIFO will be aligned with the data bytes expected by the RISC instructions. The
DMA controller reads RISC instructions and performs burst writes from the FIFO.
The DMA controller can be programmed to wait for 4, 8, 16, or 32 DWORDs
in the FIFO before executing a WRITE instruction. Setting this FIFO trigger point
optimizes the bus efficiency, by not allowing the DMA controller to access the bus
every time a DWORD enters the FIFO. However, the FIFO trigger point is ignored
in the case where the DMA controller is near the end of an instruction and the num-
ber of DWORDs left to transfer is less than the number of DWORDS in the FIFO.
By allowing the instruction to complete, even if the FIFO is below its trigger point,
the RISC instructions can be flushed sooner for every scan line. Otherwise, the
DMA controller may have to wait for many scan lines before the required number
of DWORDs are present in the FIFO, especially when capturing highly scaled
down images. There may be several horizontal lines before another DWORD en-
ters the FIFO.
The FIFO trigger point is ignored by the DMA controller during all SKIP in-
structions. In the planar mode, the trigger points for the FIFOs should be set to the
same level, even though the luma data is being stored in the Y FIFO at least twice
as fast the chroma data is being stored in the Cr and Cb FIFOs. This ensures that
the Y FIFO will be selected first to burst data onto the PCI bus.
When the initiator is disconnected from the PCI bus while in the planar mode,
it is essential to regain control of the bus as soon as possible and to deliver any
queued DWORDs. The DMA controller will ignore the FIFO trigger point as it
needs to empty the FIFO immediately, otherwise it may not have a chance to empty
the rest of the FIFOs before it has to relinquish the bus. This is not a concern in the
packed mode because all three FIFOs are treated as one large FIFO.
The DMA controller immediately stops burst data writes and RISC instruction
reads when the PCI target detects a parity error while the PCI initiator is reading
the instruction data. This condition also causes an interrupt.
FIFO Over-run
Conditions
There will be cases where the Bt848 PCI initiator cannot gain control of the PCI
bus, and the DMA controller is not able to execute the necessary WRITE instruc-
tions. Instead of writing data to the bus, the DMA controller reads data out of the
FIFO and discards the data. To the FIFO, it appears as if the DMA controller is out-
putting to the bus. This allows the FIFO over-runs to be handled gracefully, with
minimal loss of data. The Bt848 is not required to abort a whole scan during FIFO
over-runs. The DMA controller keeps track of the data to the nearest byte, and is
able to deliver the rest of the scan line in the case the FIFO over-run condition is
cleared.
The Bt848 DMA controller is normally monitoring the FIFO Full counters
(FFULL) to determine how full the FIFOs are. However, before the DMA control-
ler begins a burst write operation to process a WRITE instruction, it is desirable to
相關PDF資料 |
PDF描述 |
|---|---|
| BT8510EPJC | PCM Transceiver |
| BT857KPJ | Color Encoder Circuit |
| BT8958EHJ50 | xDSL Interface |
| BT8953AEPFC | xDSL Interface |
| BT8953AEPJ | xDSL Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BT849AKPF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single-Chip Video Capture for PCI |
| BT850-SA | 功能描述:BTV4.2 DUAL MODE USB HCI MODULE 制造商:laird - wireless & thermal systems 系列:* 零件狀態:在售 標準包裝:1 |
| BT850-SA-T/R | 功能描述:BTV4.2 DUAL MODE USB HCI MODULE 制造商:laird - wireless & thermal systems 系列:* 零件狀態:在售 標準包裝:2,500 |
| BT850-ST | 功能描述:BTV4.2 DUAL MODE USB HCI MODULE 制造商:laird - wireless & thermal systems 系列:* 零件狀態:在售 標準包裝:1 |
| BT850-ST-T/R | 功能描述:BTV4.2 DUAL MODE USB HCI MODULEE 制造商:laird - wireless & thermal systems 系列:* 零件狀態:在售 標準包裝:2,500 |
發布緊急采購，3分鐘左右您將得到回復。