- 您現在的位置：買賣IC網 > PDF目錄16544 > AD9520-5/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9520-5 PDF資料下載
參數資料
| 型號： | AD9520-5/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 68/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD9520-5 |
| 設計資源： | Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121) Phase Coherent FSK Modulator (CN0186) AD9520 Eval Brd Schematic AD9520 BOM |
| 標準包裝： | 1 |
| 主要目的： | 計時，時鐘發生器 |
| 已用 IC / 零件： | AD9520-5 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
AD9520-5
Data Sheet
Rev. A | Page 70 of 76
Table 55. EEPROM Control
Reg.
Addr.
(Hex) Bits Name
Description
0xB00 [7:1] Unused
Unused.
0
STATUS_EEPROM
(read only)
This read-only register indicates the status of the data transfer between the EEPROM and the buffer register
bank during the writing and reading of the EEPROM. This signal is also available at the STATUS pin when
Register 0x01D[7] is set.
0: data transfer is complete.
1: data transfer is not complete.
0xB01 [7:1] Unused
Unused.
0
EEPROM
data error
(read only)
This read-only register indicates an error during the data transfer between the EEPROM and the buffer.
0: no error. Data is correct.
1: incorrect data detected.
0xB02 [7:1] Unused
Unused.
1
SOFT_EEPROM
When the EEPROM pin is tied low, setting SOFT_EEPROM resets the AD9520 using the settings saved in the
EEPROM.
1: soft reset with EEPROM settings (self-clearing).
0
Enable EEPROM
write
Enables the user to write to the EEPROM.
0: EEPROM write protection is enabled. User cannot write to the EEPROM (default).
1: EEPROM write protection is disabled. User can write to the EEPROM. Once an EEPROM save/load transfer is
complete, the user must wait a minimum of 10 s before starting the next EEPROM save/load transfer.
0xB03 [7:1] Unused
Unused.
0
REG2EEPROM
Transfers data from the buffer register to the EEPROM (self-clearing).
1: setting this bit initiates the data transfer from the buffer register to the EEPROM (writing process); it is
reset by the IC master after the data transfer is complete. Once an EEPROM save/load transfer is complete,
the user must wait a minimum of 10 s before starting the next EEPROM save/load transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| ACM06DRYN | CONN EDGECARD 12POS DIP .156 SLD |
| SPD42R-823M | INDUCTOR PWR SHIELDED 82UH SMD |
| EBA30DTKS | CONN EDGECARD 60POS DIP .125 SLD |
| CDK2000-LCO | KIT EVAL PROTOTYPING CS2300-CP |
| ECE-T2GP821FA | CAP ALUM 820UF 400V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9521JH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Log/Antilog Amplifier |
| AD9521KH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Log/Antilog Amplifier |
| AD9521SE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Log/Antilog Amplifier |
| AD9521SH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Log/Antilog Amplifier |
| AD9521TE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Log/Antilog Amplifier |
發布緊急采購，3分鐘左右您將得到回復。