28F016XS FLASH MEMORY
E
10
The BYTE# pin allows either x8 or x16
read/programs to the 28F016XS. BYTE# at logic
low selects 8-bit mode with address A
selecting
between low byte and high byte. On the other hand,
BYTE# at logic high enables 16-bit operation with
address A
1
becoming the lowest order address and
address A
is not used (don’t care). A device block
diagram is shown in Figure 1.
The 28F016XS incorporates an Automatic Power
Saving (APS) feature, which substantially reduces
the active current when the device is in static mode
of operation (addresses not switching). In APS
mode, the typical I
CC
current is 1 mA at 5.0V (3 mA
at 3.3V).
A deep power-down mode of operation is invoked
when the RP# (called PWD# on the 28F008SA) pin
transitions low. This mode brings the device power
consumption to less than 2.0 μA, typically, and
provides additional write protection by acting as a
device reset pin during power transitions. A reset
time of 300 ns (5V V
CC
) is required from RP#
switching high before latching an address into the
28F016XS. In the deep power-down state, the
WSM is reset (any current operation will abort) and
the CSR, GSR and BSR registers are cleared.
A CMOS standby mode of operation is enabled
when either CE
# or CE
# transitions high and RP#
stays high with all input control pins at CMOS
levels. In this mode, the device typically draws an
I
CC
standby current of 70 μA at 5V V
CC
.
The 28F016XS is available in 56-Lead, 1.2 mm
thick, 14 mm x 20 mm TSOP and 1.8 mm thick, 16
mm x 23.7 mm SSOP Type I packages. The form
factor and pinout of these two packages allow for
very high board layout densities.
2.0
DEVICE PINOUT
The 28F016XS is pinout compatible with the
28F016SA/SV 16-Mbit FlashFile memory com-
ponents, providing a performance upgrade path to
the 28F016XS. The 28F016XS 56-Lead TSOP and
SSOP pinout configurations are shown in Figures 2
and 3.
CE #
NC
A
20
28F016SA/SV
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
34
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
35
E28F016XS
56-LEAD TSOP PINOUT
14 mm x 20 mm
TOP VIEW
3/5#
1
WP#
WE#
OE#
RY/BY#
DQ
15
GND
DQ
13
DQ
5
DQ
12
DQ
4
V
GND
DQ
11
DQ
3
DQ
10
DQ
2
V
CC
DQ
7
DQ
14
DQ
6
ADV#
CLK
DQ
9
DQ
1
DQ
8
DQ
0
A
0
A
17
A
16
A
18
A
19
V
CC
A
15
A
14
A
13
A
12
CE #
V
RP#
A
11
A
10
A
9
A
8
GND
A
7
A
6
A
5
A
4
A
3
A
2
A
1
28F016SA/SV
WP#
WE#
OE#
RY/BY#
DQ
15
GND
DQ
13
DQ
5
DQ
12
DQ
4
V
GND
DQ
11
DQ
3
DQ
10
DQ
2
V
CC
DQ
7
DQ
14
DQ
6
BYTE#
NC
NC
DQ
9
DQ
1
DQ
8
DQ
0
A
0
NC
A
20
A
17
A
16
A
18
A
19
V
CC
A
15
A
14
A
13
A
12
CE #
V
PP
RP#
A
11
A
10
A
9
A
8
GND
A
7
A
6
A
5
A
4
A
3
A
2
A
1
CE #
0
0532_02
Figure 2. 28F016XS 56-Lead TSOP Pinout Configuration Shows Compatibility with
the 28F016SA/SV, Allowing for Easy Performance Upgrades from Existing 16-Mbit Designs