參數資料
型號： SiI0680ACLU144
廠商： Silicon Image, Inc.
英文描述： PCI to IDE/ATA
中文描述： PCI到IDE / ATA的
文件頁數： 24/124頁
文件大小： 820K
代理商： SII0680ACLU144
SiI0680A PCI to IDE/ATA
Data Sheet
Silicon Image, Inc.
2006 Silicon Image, Inc.
SiI-DS-0069-C
24
3.3 PCI-680 Pin Descriptions
3.3.1 IDE/ATA Primary Channel
IDE0 Disk Data Bus
Pin Names: IDE0_DD[15..0]
Pin Numbers: 25, 24, 23, 22, 21, 20, 19, 18, 15, 14, 13, 12, 11, 10, 9, 8
Disk Data bits 0 through 15 are the 16-bit bi-directional data bus which connects to the ATA device(s). IDE0_DD[15:0] are
data signals to the primary Channel. IDE0_DD[7:0] defines the low byte while IDE0_DD[15:8] defines the high byte of this 16-
bit data register. The data bus is normally in a high impedance state and is driven by the SiI 0680A during the IDE0_DIOW_N
command pulse in either single/multi-word DMA mode, or valid at every edge of IDE0_DIOR_N (HSTROBE) or IDE0_IORDY
(DSTROBE) in Ultra DMA mode. IDE0_DD[7] is a multifunction pin which allows a host to recognize the absence of an
ATA/ATAPI device at power-up. It is recommended that a 10k
pull-down resistor be connected to this pin.
IDE0 Chip Select
Pin Names: IDE0_CS0_N; IDE0_CS1_N
Pin Numbers: 28, 29
These are the chip select signals from the host used to select the Command Block or Control Block registers. When
IDE0_DMACK_N is asserted, IDE0_CS0_N and IDE0_CS1_N shall be negated and transfers shall be 16 bits wide.
IDE0 Disk Address
Pin Names: IDE0_DA[2..0]
Pin Numbers: 32, 31, 30
Disk Address bits 0 through 2 are normally outputs to the ATA connector selecting the register in the drive’s Command Block
register. IDE0_DA[2:0] sends address signals to the primary channel. These address signals are decoded from the
PCI_AD[2:0] and PCI_CBE[3:0] inputs.
IDE0 Disk I/O Read
Pin Name: IDE0_DIOR_N
Pin Number: 33
Primary Channel Disk I/O Read is an active low output which enables data to be read from the drive. The duration and
repetition rate of IDE0_DIOR_N cycles is determined by SiI 0680A programming. IDE0_DIOR_N to the primary channel is
driven high when inactive. This signal is defined as HSTROBE in Ultra DMA write mode to write data to the primary channel
drive. This signal is also defined as primary channel HDMARDY_N in Ultra DMA read mode.
IDE0 Disk I/O Write
Pin Name: IDE0_DIOW_N
Pin Number: 34
Primary Channel Disk I/O Write is an active low output that enables data to be written to the drive. The duration and repetition
of IDE0_DIOW_N cycles is determined by SiI 0680A Programming. IDE0_DIOW_N to the primary channel is driven high when
inactive. This signal is defined as primary channel STOP in ultra DMA mode.
IDE0 DMA Acknowledge
Pin Name: IDE0_DMACK_N
Pin Number: 35
This signal is normally used by the SiI 0680A in response to IDE0_DMARQ to either acknowledge that the primary channel is
ready to accept data, or that data is available. This signal is also used to write CRC code to the primary channel drive at the
end of each Ultra DMA burst transfer.
相關PDF資料
PDF描述
SII0680 SteelVine⑩ Host Controller
SII1000 PanelLink Receivers
SII1151 TELECOMMANDER USB(PC&Mac OS X) FOR DESKTOP ROVER
SiI1151CLU CASE,MEDIUM-DUTY ABS,2807, FOAM FILLED,w/HANDLE,BLACK
SII1160 CASE,HEAVY-DUTY POLY,201407, FOAM FILLED,w/HANDLE,BLACK
相關代理商/技術參數
參數描述
SII1000 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receivers
SII100N06 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules
SII100N12 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules
SII100S12 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:絕緣柵雙極型晶體管（IGBT）Isolated Gate Bipolar Transistor (IGBTs)，SPT技術的IGBT模塊SPT IGBT Modules (Soft Punch Through Technology)。
SII1151 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*