- 您現在的位置：買賣IC網 > PDF目錄365565 > SiI0680ACL144 (Silicon Image, Inc.) PCI to IDE/ATA PDF資料下載
參數資料
| 型號： | SiI0680ACL144 |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | PCI to IDE/ATA |
| 中文描述： | PCI到IDE / ATA的 |
| 文件頁數： | 115/124頁 |
| 文件大小： | 820K |
| 代理商： | SII0680ACL144 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁當前第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
Silicon Image, Inc.
SiI0680A PCI to IDE/ATA
Data Sheet
2006 Silicon Image, Inc.
SiI-DS-0069-C
115
11. If bit 11 is set, the ATA/ATAPI device is interrupting and should be serviced by following the
steps below (assuming that the virtual DMA operation completed successfully).
If the ATA/ATAPI device has interrupted,
Read the device status at bits [31:24] in the IDEx Task File Register 1 register to clear the device
interrupt and determine if there was an error.
Write 1 to bit 18 of the PCI Bus Master – IDEx register to clear the DMA Complete bit (NOTE: The
DMA Complete bit acts as a latched copy of the ATA interrupt line when the channel is not
performing a DMA operation).
If the ATA/ATAPI device is not reporting an error, and DRQ is asserted (bit 27 of IDEx Task File
Register 1), then the device is interrupting to transfer data to the host. To transfer the data, the
DMA registers are setup to only perform that part of the data transfer expected for this interrupt.
The DMA is setup similarly to the way it is when performing a normal read DMA command, but with
one additional step. Before the DMA is enabled, the IDEx Virtual DMA/PIO Read Ahead Byte
Count register must be written with the 32-bit count of the number of bytes to be transferred for this
interrupt.
Repeat the above steps until all data for the read command has been transferred or an error has been
detected.
Write Operation
Poll the IDEx Task File Register 1 bits [31:24] until either bit 27 (DRQ) is set indicating the device is ready for
write data transfer, or bit 24 (ERR) is set indicating the device has detected an error with the write command.
If no error, and DRQ is asserted (bit 27 of IDEx Task File Register 1), then the device is waiting for write data
transfer. To transfer the data, the DMA registers are setup to only perform that part of the data transfer
expected at this time. For example, a Write Sectors command would expect to transfer 1 sector (512 bytes),
while a Write Multiple command would expect to transfer the lesser of the number of sectors set by the Set
Multiple Mode command or the total number of sectors specified by the Write Multiple command. The DMA
is setup similarly to the way it is when performing a normal write DMA command, but with one additional
step. Before the DMA is enabled, the IDEx Virtual DMA/PIO Read Ahead Byte Count register must be
written with the 32-bit count of the number of bytes to be transferred.
Wait for a PCI interrupt.
Read the DMA status bits [18:16] of the PCI Bus Master – IDEx register, and check that bit 18 is set to make
sure the interrupt was generated by the expected channel.
If expected channel interrupted, read bits [11:10] of the channel’s IDEx Task File Timing + Configuration +
Status register to determine the cause of the interrupt. Bit 11 is set if the ATA/ATAPI device has an interrupt
pending, bit 10 is set if a virtual DMA operation completed.
If a virtual DMA operation completed,
Write 00
H
to bits [7:0] of the PCI Bus Master – IDEx register to disable DMA operation.
Write 1 to bits [18:17] of the PCI Bus Master –IDEx register to reset the DMA status and virtual
DMA interrupt bits, and PCI interrupt.
Check the previously read DMA status bits to ensure the DMA completed successfully. See section
11.8 for more information about interpreting the DMA status bits.
Because ATA/ATAPI commands that transfer data using PIO can generate several interrupts
during the data transfer phase of the command, a race condition is created between the interrupt
indicating the completion of a virtual DMA operation, and the interrupt from the ATA/ATAPI device
indicating it is ready to perform the next part of the data transfer. To prevent missing an
ATA/ATAPI device interrupt due to this race condition, it is necessary to re-read the channel’s IDEx
Task File Timing + Configuration + Status register after disabling DMA operation and examining bit
11. If bit 11 is set, the ATA/ATAPI device is interrupting and should be serviced by following the
steps below (assuming that the virtual DMA operation completed successfully).
相關PDF資料 |
PDF描述 |
|---|---|
| SiI0680ACLU144 | PCI to IDE/ATA |
| SII0680 | SteelVine⑩ Host Controller |
| SII1000 | PanelLink Receivers |
| SII1151 | TELECOMMANDER USB(PC&Mac OS X) FOR DESKTOP ROVER |
| SiI1151CLU | CASE,MEDIUM-DUTY ABS,2807, FOAM FILLED,w/HANDLE,BLACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII0680ACLU144 | 制造商:Silicon Image Inc 功能描述:STEELVINE HOST CONTROLLER |
| SII1000 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receivers |
| SII100N06 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
| SII100N12 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
| SII100S12 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:絕緣柵雙極型晶體管（IGBT）Isolated Gate Bipolar Transistor (IGBTs)，SPT技術的IGBT模塊SPT IGBT Modules (Soft Punch Through Technology)。 |
發布緊急采購，3分鐘左右您將得到回復。