- 您現在的位置：買賣IC網 > PDF目錄365565 > SiI0680ACL144 (Silicon Image, Inc.) PCI to IDE/ATA PDF資料下載
參數資料
| 型號： | SiI0680ACL144 |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | PCI to IDE/ATA |
| 中文描述： | PCI到IDE / ATA的 |
| 文件頁數： | 114/124頁 |
| 文件大小： | 820K |
| 代理商： | SII0680ACL144 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁當前第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
SiI0680A PCI to IDE/ATA
Data Sheet
Make sure PCI bus master operation of the SiI 0680A is stopped by clearing bit 0 of the PCI Bus Master –
IDEx register.
Note: The task file registers are not accessible as long as bit 0 is set. Clearing bit 0 causes bit 16 to be
cleared as well.
Read the device status at bits [13:24] in the IDEx Task File Register 1 register to clear the device interrupt
and determine if there was error.
Write ‘1’ to bit 18 (write-one-to-clear) in the PCI Bus Master – IDEx register to clear the PCI Interrupt.
Silicon Image, Inc.
2006 Silicon Image, Inc.
SiI-DS-0069-C
114
11.9 IDE Virtual DMA Read/Write Operation
In virtual DMA operation the controller uses a PIO data transfer mode to move data between an ATA/ATAPI device and the
controller, and uses DMA to move that same data between the controller and the host memory. For ATA/ATAPI devices that
cannot operate in a “true” DMA mode, virtual DMA provides two benefits; first, using DMA to move data reduces the demand
on the host CPU, and second, systems that use virtual memory often require that data buffers that will be accessed directly by
low level device drivers be “mapped” into the operating system’s address space, in virtual DMA mode the CPU does not
access the data buffer directly, so the overhead of obtaining the mapping to operating system address space is eliminated.
11.9.1 Using Virtual DMA with Non-DMA Capable Devices
Once the SiI 0680A is initialized via the initialization sequence described in Section 11.1, the ATA device has been initialized
for PIO mode data transfer per the guidelines in section 11.2, and the controller channel has been initialized for PIO mode data
transfer per the instructions in section 11.3, virtual DMA read/write operations may be performed by following the programming
sequence described below.
NOTE:
The watchdog timer feature is compatible with virtual DMA operation. See section 11.7 for details about using the
watchdog timer.
Issue a PIO read/write command to the device following steps in section 11.4.
Read Operation
Wait for a PCI interrupt.
Read the DMA status bits [18:16] of the PCI Bus Master – IDEx register, and check that bit 18 is set to make
sure the interrupt was generated by the expected channel.
If expected channel interrupted, read bits [11:10] of the channel’s IDEx Task File Timing + Configuration +
Status register to determine the cause of the interrupt. Bit 11 is set if the ATA/ATAPI device has an interrupt
pending, bit 10 is set if a virtual DMA operation completed.
If a virtual DMA operation completed,
Write 00
H
to bits [7:0] of the PCI Bus Master – IDEx register to disable DMA operation.
Write 1 to bits [18:17] of the PCI Bus Master –IDEx register to reset the DMA status and virtual
DMA interrupt bits, and the PCI interrupt.
Check the previously read DMA status bits to ensure the DMA completed successfully. See section
11.8 for more information about interpreting the DMA status bits.
Because ATA/ATAPI commands that transfer data using PIO can generate several interrupts
during the data transfer phase of the command, a race condition is created between the interrupt
indicating the completion of a virtual DMA operation, and the interrupt from the ATA/ATAPI device
indicating it is ready to perform the next part of the data transfer. To prevent missing an
ATA/ATAPI device interrupt due to this race condition, it is necessary to re-read the channel’s IDEx
Task File Timing + Configuration + Status register after disabling DMA operation and examining bit
相關PDF資料 |
PDF描述 |
|---|---|
| SiI0680ACLU144 | PCI to IDE/ATA |
| SII0680 | SteelVine⑩ Host Controller |
| SII1000 | PanelLink Receivers |
| SII1151 | TELECOMMANDER USB(PC&Mac OS X) FOR DESKTOP ROVER |
| SiI1151CLU | CASE,MEDIUM-DUTY ABS,2807, FOAM FILLED,w/HANDLE,BLACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII0680ACLU144 | 制造商:Silicon Image Inc 功能描述:STEELVINE HOST CONTROLLER |
| SII1000 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receivers |
| SII100N06 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
| SII100N12 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
| SII100S12 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:絕緣柵雙極型晶體管（IGBT）Isolated Gate Bipolar Transistor (IGBTs)，SPT技術的IGBT模塊SPT IGBT Modules (Soft Punch Through Technology)。 |
發布緊急采購，3分鐘左右您將得到回復。