- 您現在的位置：買賣IC網 > PDF目錄365565 > SII0680A (Silicon Image, Inc.) PCI to IDE/ATA PDF資料下載
參數資料
| 型號： | SII0680A |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | PCI to IDE/ATA |
| 中文描述： | PCI到IDE / ATA的 |
| 文件頁數： | 16/124頁 |
| 文件大?。?/td> | 820K |
| 代理商： | SII0680A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
SiI0680A PCI to IDE/ATA
Data Sheet
2.5 Power Supply Bypass Considerations
It is recommended that a 4-layer board (minimum) with internal Power and Ground Planes be used when i integrating the SiI
0680A . Good high-speed layout techniques should be used and proper power supply bypassing is essential. Both bulk and
local (high frequency) bypass capacitors should be used.
Bulk bypassing is intended to reduce the voltage noise (droop) induced by changes in load current and the inductance in the
power distribution system (wires and/or etch). Since the currents vary greatly from no activity to worst case data patterns, a
significant amount of capacitance is required.
All bypass capacitors should be connected to the power and ground plane with a low inductance connection (short, wide traces
connecting component pad to plane).
The bulk bypass capacitor(s) should have good high frequency characteristics. A capacitor with low ESR (Equivalent Series
Resistance) should be used. It should be located close to the source of +3.3V (output pin of regulator or connector pin for off
board regulators). The following minimum values are recommended:
Low ESR Tantalum – 100uF
Low ESR Aluminum Electrolytic – 600uF
Local high frequency 0bypass should also be implemented. Capacitors should be located on all four sides of the chip close to
the VDD/VSS pins. Three caps per side are recommended (12 total). Additional capacitors (x6) should be distributed evenly
around the board area.
The following capacitor is recommended for local bypass:
Ceramic X7R Dielectric - 0.01uF
For a slight improvement in high frequency impedance of the bypass capacitors, two capacitors in parallel can be used for
Local Bypass. The paired caps must be located as close as possible to each other. The following values are recommended
for the capacitor pairs:
Ceramic X7R Dielectric - 0.1uF
Ceramic X7R Dielectric – 1000pF
Silicon Image, Inc.
2006 Silicon Image, Inc.
SiI-DS-0069-C
16
相關PDF資料 |
PDF描述 |
|---|---|
| SiI0680ACL144 | PCI to IDE/ATA |
| SiI0680ACLU144 | PCI to IDE/ATA |
| SII0680 | SteelVine⑩ Host Controller |
| SII1000 | PanelLink Receivers |
| SII1151 | TELECOMMANDER USB(PC&Mac OS X) FOR DESKTOP ROVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII0680ACL144 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to IDE/ATA |
| SII0680ACLU144 | 制造商:Silicon Image Inc 功能描述:STEELVINE HOST CONTROLLER |
| SII1000 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receivers |
| SII100N06 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
| SII100N12 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
發布緊急采購，3分鐘左右您將得到回復。