- 您現在的位置：買賣IC網 > PDF目錄365565 > SII0680A (Silicon Image, Inc.) PCI to IDE/ATA PDF資料下載
參數資料
| 型號： | SII0680A |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | PCI to IDE/ATA |
| 中文描述： | PCI到IDE / ATA的 |
| 文件頁數： | 109/124頁 |
| 文件大小： | 820K |
| 代理商： | SII0680A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁當前第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
Silicon Image, Inc.
SiI0680A PCI to IDE/ATA
Data Sheet
2006 Silicon Image, Inc.
SiI-DS-0069-C
109
enabled, command completion can be detected by polling bits [31:24] of the IDEx Task
File Register 1 register until the BUSY bit is no longer asserted.
If device supports read/write multiple commands, issue the Set Multiple Mode command by:
Programming bits [23:16] in the IDEx Task File 0 register with the number of sectors per
block to use on the following Read/Write Multiple commands.
Programming bits [31:24] in the IDEx Task File Register 1 register with the value = C6
H
.
Wait for the command to complete (see above).
For both ATA and ATAPI devices:
Set device transfer mode by:
Programming bits [15:08] in the IDEx Task File 0 register with the value 03
H
to “Set the
transfer mode based on value in Sector Count Register”.
Programming bits [23:16] in the IDEx Task File 0 register to the desired transfer mode.
The settings are defined below:
08
H
= PIO Mode 0
09
H
= PIO Mode 1
0A
H
= PIO Mode 2
0B
H
= PIO Mode 3
0C
H
= PIO Mode 4
20
H
= Multiword DMA Mode 0
21
H
= Multiword DMA Mode 1
22
H
= Multiword DMA Mode 2
40
H
= Ultra DMA Mode 0
41
H
= Ultra DMA Mode 1
42
H
= Ultra DMA Mode 2
43
H
= Ultra DMA Mode 3
44
H
= Ultra DMA Mode 4
45
H
= Ultra DMA Mode 5
46
H
= Ultra DMA Mode 6
Programming bits [31:24] in the IDEx Task File Register 1 register with the value = EF
H
.
Wait for the command to complete (see above).
NOTE: An 80-pin cable is required to ensure signal quality can be maintained for transfer modes
higher than Ultra DMA mode 2. When bit 0 of the IDEx Task File Timing + Configuration + Status
register is set, an 80-pin cable may be present (see the ATA/ATAPI specification for details on how
this bit should be interpreted).
11.3 Initialization of Controller Channel Timing Registers
There are four types of timing registers associated with a channel.
The IDEx Task File Timing + Configuration + Status register controls the timing of ATA/ATAPI device task file register
accesses (except for accesses to the data register). Since this register controls the task file access timing for all devices
attached to the channel, it is important to program this register with values that do not exceed the capabilities of the slowest
device attached to the channel.
The IDEx PIO Timing register controls the access timing of the task file data register when programmed I/O is used to transfer
data to or from the device.
The IDEx DMA Timing register controls the data transfer timing when the device and controller have been setup to use a
multiword DMA transfer mode.
The IDEx UDMA Timing register controls the data transfer timing when the device and controller have been setup to use an
Ultra DMA transfer mode.
Data transfer timing can be set independently for each device. The following steps need to be performed to configure the
controller timing to match the transfer mode selected for the ATA/ATAPI device:
Set the task file register access timing. The task file register timing is set by programming bits [31:16] of the
IDEx Task File Timing + Configuration + Status register. See section 13.2.1 for recommended values to
相關PDF資料 |
PDF描述 |
|---|---|
| SiI0680ACL144 | PCI to IDE/ATA |
| SiI0680ACLU144 | PCI to IDE/ATA |
| SII0680 | SteelVine⑩ Host Controller |
| SII1000 | PanelLink Receivers |
| SII1151 | TELECOMMANDER USB(PC&Mac OS X) FOR DESKTOP ROVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII0680ACL144 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to IDE/ATA |
| SII0680ACLU144 | 制造商:Silicon Image Inc 功能描述:STEELVINE HOST CONTROLLER |
| SII1000 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PanelLink Receivers |
| SII100N06 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
| SII100N12 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
發布緊急采購，3分鐘左右您將得到回復。