- 您現在的位置：買賣IC網 > PDF目錄369993 > Pentium III cpu with mobile (Intel Corp.) Pentium III processor Mobile Module Connector 2 (MMC-2)(帶移動模塊連接器2奔III處理器) PDF資料下載
參數資料
| 型號： | Pentium III cpu with mobile |
| 廠商： | Intel Corp. |
| 英文描述： | Pentium III processor Mobile Module Connector 2 (MMC-2)(帶移動模塊連接器2奔III處理器) |
| 中文描述： | 奔騰III處理器的移動模塊連接器2（絲裂霉素2）（帶移動模塊連接器2奔三處理器） |
| 文件頁數： | 32/64頁 |
| 文件大小： | 773K |
| 代理商： | PENTIUM III CPU WITH MOBILE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
Pentium
III Processor Mobile Module MMC-2
26
Datasheet
245304-003
RESET# assertion will cause the processor to immediately initialize itself, but the processor will
stay in the Quick Start state after initialization until STPCLK# is deasserted.
4.4.1.5
HALT/Grant Snoop State
The processor will respond to snoop transactions on the PSB while in the Auto Halt, Stop Grant, or
Quick Start state. When a snoop transaction is presented on the system bus, the processor will enter
the HALT/Grant Snoop state. The processor will remain in this state until the snoop has been
serviced and the PSB is quiet. After the snoop has been serviced, the processor will return to its
previous state. If the HALT/Grant Snoop state is entered from the Quick Start state, then the input
signal restrictions of the Quick Start state still apply in the HALT/Grant Snoop state (except for
those signal transitions that are required to perform the snoop).
4.4.1.6
Sleep State
Intel mobile modules do not support the Sleep state.
In desktop systems, the Sleep state is a very low-power state in which the processor maintains its
context and the phase locked loop (PLL) maintains phase lock. The Sleep state can only be entered
from the Stop Grant state. After entering the Stop Grant state the SLP# signal can be asserted,
causing the processor to enter the Sleep state. The SLP# signal is not recognized in the Normal
state or the Auto Halt state.
The processor can be reset by the RESET# signal while in the Sleep state. If RESET# is driven
active while the processor is in the Sleep state, then SLP# and STPCLK# must immediately be
driven inactive to ensure that the processor correctly initializes itself.
Input signals (other than RESET#) may not change while the processor is in or transitioning into or
out of the Sleep state. Input signal changes at these times will cause unpredictable behavior. Thus,
the processor is incapable of snooping or latching any events in the Sleep state.
While in the Sleep state the processor can enter its lowest power state, the Deep Sleep state.
Removing the processor
’
s input clock puts the processor in the Deep Sleep state. PICCLK may be
removed in the Sleep state.
4.4.1.7
Deep Sleep State
The Deep Sleep state is the lowest power mode the processor can enter while maintaining its
context. Stopping the BCLK input to the processor enters the Deep Sleep state, while it is in the
Sleep state or the Quick Start state. For proper operation, the BCLK input should be stopped in the
low state.
The processor will return to the Sleep state or the Quick Start state from the Deep Sleep state when
the BCLK input is restarted. Due to the PLL lock latency, there is a 30-
μ
S delay after the clocks
have started before this state transition happens. PICCLK may be removed in the Deep Sleep state.
PICCLK should be designed to turn on when BCLK turns on when transitioning out of the Deep
Sleep state.
The input signal restrictions for the Deep Sleep state are the same as for the Sleep state, except that
RESET# assertion will result in unpredictable behavior.
相關PDF資料 |
PDF描述 |
|---|---|
| pentium III CPU | Pentium III Processor for the SC242 at 450MHz to 1.0GHz(SC242工作頻率450MHZ到1GHZ奔III處理器) |
| pentium III processor | 32 bit Processor Mobile Module(32 位帶移動模塊處理器) |
| Pentium OverDrive Processor | Pentium OverDrive Processor With MMX Technology For Pentium Processor-Based System(帶MMX技術奔騰超速轉動處理器) |
| pentium pro processor | Pentium Pro Processor with 1MB L2 Cache at 200MHZ(1兆比特L2高速緩存頻率200兆赫茲處理器) |
| pentium processor with MMX | 32-bit processor with MMX technology(32位帶MMX技術處理器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P-ENV568K3G3 | 制造商:Panasonic Industrial Company 功能描述:TUNER |
| PEO14012 | 制造商:TE Connectivity 功能描述:RELAY SPCO 12VDC |
| PEO14024 | 制造商:TE Connectivity 功能描述:RELAY SPCO 24VDC |
| PEO96742 | 制造商:Delphi Corporation 功能描述:ASM TERM |
| PEOODO3A | 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:Versatile Power Entry Module with Small Footprint |
發布緊急采購，3分鐘左右您將得到回復。