- 您現在的位置：買賣IC網 > PDF目錄384760 > MT9071 (Mitel Networks Corporation) Quad T1/E1/J1 Transceiver(多端口 T1/E1/J1幀調節器（集成四個獨立幀調節器）) PDF資料下載
參數資料
| 型號： | MT9071 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | Quad T1/E1/J1 Transceiver(多端口 T1/E1/J1幀調節器（集成四個獨立幀調節器）) |
| 中文描述： | 四T1/E1/J1收發器（多端口的T1/E1/J1幀調節器（集成四個獨立幀調節器）） |
| 文件頁數： | 62/217頁 |
| 文件大?。?/td> | 686K |
| 代理商： | MT9071 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁
MT9071
Preliminary Information
62
The lower nibble of a CSTi/CSTo timeslot is used for the four signaling bits, the upper nibble on the CSTo
timeslots is not used and is either high or low. All unused CSTo timeslots are high impedance. In order to
facilitate multiplexing on the CSTo control streams, control register bit CSToEn (Table 178 - T1 Interrupt and I/
O Control - R/W Address YF1) will place the whole stream in a high impedance state when set low.
In the case of D4 trunks, only AB bits are reported. The control register bits SM1-0 (Table 86 - T1 Signalling
Control - R/W Address Y04) allow the user to program the 2 unused bits (CD) reported on CSTo.
A receive signaling bit debounce of 6ms can be selected with control register bit RSDB (Table 86 - T1
Signalling Control - R/W Address Y04).
It should be noted that there may be as much as 3ms added to this
duration because signaling equipment state changes are not synchronous with the D4 or ESF multiframe.
If multiframe synchronization is lost, as indicated by status register bit MFSYNC =1 (Table 104 - T1
Synchronization and Alarm Status - R Address Y10), then the CAS bits will be frozen (i.e. will retain their
previous value and will not be updated). The CAS bits are unfrozen when multiframe synchronization is
acquired (this is the same as terminal frame synchronization for ESF links).
CAS signaling freeze due to receiver slip is also available by setting control register bit RFS =1 (Table 86 - T1
Signalling Control - R/W Address Y04).
A CAS state change on any of the 24 receive channels will cause the following events to occur:
The latched status register bit CASRL = 1 (see Table 134 - T1 Receive Line Status and Timer Latch - R
Address Y25).
The interrupt status register bit CASRI = 1 (see Table 151 - T1 Receive Line and Timer Interrupt Status
- R Address Y35), if unmasked with mask control register bit CASRM = 0 (see Table 158 - T1 Receive
Line and Timer Interrupt Mask - R/W Address Y45).
When the CASRI interrupt is unmasked, IRQ will become active when a signaling state change is detected in
any of the 24 receive channels and the selectable 1/4/8/16 msec timer (see control bits SIP1,0 detailed Table
86 - T1 Signalling Control - R/W Address Y04) has expired. This function helps to reduce the frequency of
interrupts generated due to signaling changes. For instance if 7 channels had a signaling change, only one
interrupt will be generated in a 1/4/8/16 msec duration. Upon an interrupt, the user has to read the CAS
registers (Table 164 - T1 Receive CAS Data Registers - R Address Y70-Y87) to determine the channels with a
signaling change. Any channels marked as clear channels will not generate an interrupt due to changes in
ABCD bits.
10.2 E1 CAS
The purpose of the CAS Multiframing algorithm is to provide a scheme that will allow the association of a
specific ABCD signaling nibble with the appropriate PCM30 channel. A CAS multiframe consists of 16 basic
frames (numbered 0 to 15), which results in a multiframe repetition rate of 2ms. It should be noted that the
boundaries of the signaling multiframe may be completely distinct from those of the CRC-4 multiframe. CAS
multiframe alignment is based on a multiframe alignment signal (a 0000 bit sequence), which occurs in the
most significant nibble of timeslot 16 of basic frame 0 of the CAS multiframe. Bits 5, 7 and 8 (usually
designated X) are spare bits and are normally set to one if not used. Bit 6 of this timeslot is the multiframe
alarm bit (usually designated Y). When CAS multiframing is acquired on the receive side, the transmit Y-bit is
zero; when CAS multiframing is not acquired, the transmit Y-bit is one. Refer to ITU-T G.704 and G.732 for
more details on CAS multiframing requirements.
Timeslot 16 of the remaining 15 basic frames of the CAS multiframe (i.e., basic frames 1 to 15) are reserved for
the ABCD signaling bits for the 30 payload channels. The most significant nibbles are reserved for channels 1
to 15 and the least significant nibbles are reserved for channels 16 to 30. That is, timeslot 16 of basic frame 1
has ABCD for channel 1 and 16, timeslot 16 of basic frame 2 has ABCD for channel 2 and 17, through to
timeslot 16 of basic frame 15 has ABCD for channel 15 and 30. See Table 20 - E1 CAS Multiframe Structure.
相關PDF資料 |
PDF描述 |
|---|---|
| MT9072 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MT90820 | Large Digital Switch(大數字開關) |
| MT90823 | 3V Large Digital Switch(3V 大數字開關) |
| MT90826 | Quad Digital Switch(四數字開關) |
| MT90840 | Distributed Hyperchannel Switch(分布式超級通道開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT90710 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:High-Speed Isochronous Multiplexer |
| MT90710AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:High-Speed Isochronous Multiplexer |
| MT9072 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Octal T1/E1/J1 Framer |
| MT9072AB | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Octal T1/E1/J1 Framer |
| MT9072AV | 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 3.3V 256BGA - Trays 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 256BGA - Trays |
發布緊急采購，3分鐘左右您將得到回復。