參數資料
型號： ISP1362
廠商： NXP Semiconductors N.V.
英文描述： Single-chip Universal Serial Bus On-The-Go controller
中文描述： 單芯片通用串行總線和On - The - Go控制器
文件頁數： 88/150頁
文件大小： 647K
代理商： ISP1362
Philips Semiconductors
ISP1362
Single-chip USB OTG controller
Product data
Rev. 03
—
06 January 2004
88 of 150
9397 750 12337
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Table 62:
Bit
31 to 21
20
HcRhPortStatus[1:2] register: bit description
Symbol
Description
-
reserved
PRSC
PortResetStatusChange:
This bit is set at the end of the 10 ms
port reset signal. The HCD can write logic 1 to clear this bit.
Writing logic 0 has no effect.
0
—
port reset is not complete
1
—
port reset is complete
PortOverCurrentIndicatorChange:
This bit is valid only if
overcurrent conditions are reported on a per-port basis. This bit is
set when the Root Hub changes the PortOverCurrentIndicator
(POCI) bit. The HCD can write logic 1 to clear this bit. Writing
logic 0 has no effect.
19
OCIC
0
—
no change in PortOverCurrentIndicator (POCI)
1
—
PortOverCurrentIndicator (POCI) has changed
PortSuspendStatusChange:
This bit is set when the full resume
sequence is complete. This sequence includes the 20 ms resume
pulse, LS EOP and 3 ms re-synchronization delay. The HCD can
write logic 1 to clear this bit. Writing logic 0 has no effect. This bit is
also cleared when ResetStatusChange is set.
18
PSSC
0
—
resume is not completed
1
—
resume is completed
PortEnableStatusChange:
This bit is set when hardware events
cause the PortEnableStatus (PES) bit to be cleared. Changes from
the HCD writes do not set this bit. The HCD can write logic 1 to
clear this bit. Writing logic 0 has no effect.
17
PESC
0
—
no change in PortEnableStatus (PES)
1
—
change in PortEnableStatus (PES)
ConnectStatusChange:
This bit is set whenever a connect or
disconnect event occurs. The HCD can write logic 1 to clear this
bit. Writing logic 0 has no effect. If CurrentConnectStatus (CCS) is
cleared when a SetPortReset, SetPortEnable or SetPortSuspend
write occurs, this bit is set to force the driver to re-evaluate the
connection status because these writes should not occur if the port
is disconnected.
16
CSC
0
—
no change in CurrentConnectStatus (CCS)
1
—
change in CurrentConnectStatus (CCS)
Remark:
If the DeviceRemovable[NDP] bit is set, this bit is set only
after a Root Hub reset to inform the system that the device is
attached.
reserved
15 to 10
-
相關PDF資料
PDF描述
ISP1362BD Single-chip Universal Serial Bus On-The-Go controller
ISP1362EE Single-chip Universal Serial Bus On-The-Go controller
ISP1501 Hi-Speed Universal Serial Bus peripheral transceiver
ISP1520 Hi-Speed Universal Serial Bus hub controller
ISP1520BD Hi-Speed Universal Serial Bus hub controller
相關代理商/技術參數
參數描述
ISP1362BD 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,118 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,151 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,157 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD157 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB-OTG 64LQFP 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 64-LQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*