參數資料
型號： ISP1362
廠商： NXP Semiconductors N.V.
英文描述： Single-chip Universal Serial Bus On-The-Go controller
中文描述： 單芯片通用串行總線和On - The - Go控制器
文件頁數： 120/150頁
文件大小： 647K
代理商： ISP1362
Philips Semiconductors
ISP1362
Single-chip USB OTG controller
Product data
Rev. 03
—
06 January 2004
120 of 150
9397 750 12337
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Code (Hex): 01 to 0F
—
write (control IN, endpoint 1 to 14)
Code (Hex): 10, 12 to 1F
—
read (control OUT, endpoint 1 to 14)
Transaction
—
write or read maximum N
+
2 bytes (isochronous endpoint: N
≤
1023,
bulk/interrupt endpoint: N
≤
32) (code or data)
The data in the endpoint buffer memory must be organized as shown in
Table 122
. An
example of endpoint buffer memory access is given in
Table 123
.
Remark:
There is no protection against writing or reading past a buffer
’
s boundary,
against writing into an OUT buffer or reading from an IN buffer. Any of these actions
could cause an incorrect operation. Data residing in an OUT buffer is only meaningful
after a successful transaction. Exception: during DMA access of a double-buffered
endpoint, the buffer pointer automatically points to the secondary buffer after
reaching the end of the primary buffer.
16.2.2
Read Endpoint Status (R: 50H
–
5FH)
This command is used to read the status of an endpoint buffer memory. The
command accesses the DcEndpointStatus register, the bit allocation of which is
shown in
Table 124
. Reading the DcEndpointStatus register will clear the interrupt bit
set for the corresponding endpoint in the DcInterrupt register (see
Table 140
).
All bits of the DcEndpointStatus register are read-only. Bit EPSTAL is controlled by
the Stall or Unstall commands and by the reception of a SET-UP token (see
Section 16.2.3
).
Code (Hex): 50 to 5F
—
read (control OUT, control IN, endpoint 1 to 14)
Transaction
—
read 1 byte (code only)
Table 122: Endpoint buffer memory organization
Word #
0 (lower byte)
0 (upper byte)
1 (lower byte)
1 (upper byte)
…
M = (N + 1)/2
Description
packet length (lower byte)
packet length (upper byte)
data byte 1
data byte 2
…
data byte N
Table 123: Example of endpoint buffer memory access
A0
Phase
Bus lines
HIGH
command
D[7:0]
D[15:8]
LOW
data
D[15:0]
LOW
data
D[15:0]
LOW
data
D[15:0]
…
…
…
Word #
-
-
0
1
2
…
Description
command code (00H to 1FH)
ignored
packet length
data word 1 (data byte 2, data byte 1)
data word 2 (data byte 4, data byte 3)
…
相關PDF資料
PDF描述
ISP1362BD Single-chip Universal Serial Bus On-The-Go controller
ISP1362EE Single-chip Universal Serial Bus On-The-Go controller
ISP1501 Hi-Speed Universal Serial Bus peripheral transceiver
ISP1520 Hi-Speed Universal Serial Bus hub controller
ISP1520BD Hi-Speed Universal Serial Bus hub controller
相關代理商/技術參數
參數描述
ISP1362BD 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,118 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,151 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,157 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD157 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB-OTG 64LQFP 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 64-LQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*