參數資料
型號： ISP1362
廠商： NXP Semiconductors N.V.
英文描述： Single-chip Universal Serial Bus On-The-Go controller
中文描述： 單芯片通用串行總線和On - The - Go控制器
文件頁數： 61/150頁
文件大?。?/td> 647K
代理商： ISP1362
Philips Semiconductors
ISP1362
Single-chip USB OTG controller
Product data
Rev. 03
—
06 January 2004
61 of 150
9397 750 12337
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Table 23:
Bit
15 to 12 -
11
OtgControl register: bit description
Symbol
Description
reserved
OTG_SE0_
EN
0
—
No SE0 sent on remote connect detection
This bit is used by the HC to send SE0 on remote connect.
1
—
SE0 (bus reset) sent on remote connect detection
Remark:
This bit is normally set when the B-device goes into the
b_wait_acon state (recommended sequence:
LOC_CONN = 0 -> DELAY-> 50
μ
s -> OTG_SE0_EN = 1 ->
SEL_HC_DC = 0) and is cleared when it comes out of the
b_wait_acon state.
This bit is for the A-device only. If set, the A_SRP_DET bit in the
OtgInterrupt register will be set on detecting an SRP event.
10
A_SRP_
DET_EN
0
—
disable
1
—
enable
This bit is for the A-device to select a method for detecting the SRP
event (V
BUS
pulsing or data line pulsing).
9
A_SEL_
SRP
0
—
A-device responds to V
BUS
pulsing
1
—
A-device responds to data line pulsing
This bit is used to select either the DC or the HC that interfaces with
the transceiver.
8
SEL_HC_
DC
0
—
HC SIE is connected to the OTG transceiver
1
—
DC SIE is connected to the OTG transceiver
0
—
disconnects the on-chip pull-down resistor on DM of the OTG
port
7
LOC_
PULLDN_
DM
1
—
connects the on-chip pull-down resistor on DM of the OTG port
0
—
disconnects the on-chip pull-down resistor on DP of the OTG
port
6
LOC_
PULLDN_
DP
1
—
connects the on-chip pull-down resistor on DP of the OTG port
This bit is for the A-device only. If set, the chip will automatically
enable its pull-up resistor on DP upon detecting a remote disconnect
event. If cleared, the DP pull-up is controlled by the LOC_CONN bit.
5
A_RDIS_
LCON_EN
0
—
disable
1
—
enable
Remark:
This bit is normally set when the A-device goes into the
a_suspend state and is cleared when it comes out of the a_suspend
state. The LOC_CONN bit must be set before clearing this bit.
相關PDF資料
PDF描述
ISP1362BD Single-chip Universal Serial Bus On-The-Go controller
ISP1362EE Single-chip Universal Serial Bus On-The-Go controller
ISP1501 Hi-Speed Universal Serial Bus peripheral transceiver
ISP1520 Hi-Speed Universal Serial Bus hub controller
ISP1520BD Hi-Speed Universal Serial Bus hub controller
相關代理商/技術參數
參數描述
ISP1362BD 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,118 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,151 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,157 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD157 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB-OTG 64LQFP 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 64-LQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*