參數資料
型號： ISP1362
廠商： NXP Semiconductors N.V.
英文描述： Single-chip Universal Serial Bus On-The-Go controller
中文描述： 單芯片通用串行總線和On - The - Go控制器
文件頁數： 26/150頁
文件大?。?/td> 647K
代理商： ISP1362
Philips Semiconductors
ISP1362
Single-chip USB OTG controller
Product data
Rev. 03
—
06 January 2004
26 of 150
9397 750 12337
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
write_reg16(HcTransferCnt,word_size*2);
outport(hc_com,HcATL_Port|0x80); // hc_com is system address of HC
// command port
cnt=0;
do
{
outport(hc_data,*(a_ptr+cnt)); // hc_data is system address of HC
// data port
cnt++;
}
while(cnt<(word_size));
Remark:
The HcTransferCounter register counts the number of bytes even though
the transfer is in number of words. Therefore, the transfer counter should be set to
word_size
×
2. Incorrect setting of the HcTransferCounter register may cause the
ISP1362 to go into an indeterminate state.
The buffer memory access using indirect addressing always starts from the location 0
of each buffer area. Only the front portion of the memory (example:
fi
rst 64 bytes of a
1024 bytes buffer) can be accessed. Therefore, to access a portion of the memory
that does not start from memory location 0, all memory locations before that location
must be accessed in a sequential order. The method is similar to the sequential
fi
le
access method.
9.6 Setting up a DMA transfer
The ISP1362 uses two DMA channels to individually serve the HC and the DC. The
DMA transfer allows the system CPU to work on other tasks while the DMA controller
transfers data to or from the ISP1362. The DMA slave controller, in the ISP1362, is
compatible with the 8327 type DMA controller.
The DMA transfer can be used with the direct addressing mode or the indirect
addressing mode. The registers used in these two modes are shown in
Table 6
.
[1]
In the direct addressing mode, HcTransferCounter must be set to 0001H.
9.6.1
Con
fi
guring registers for a DMA transfer
To set up a DMA transfer, the following HC registers must be con
fi
gured depending
on the type of transfer required:
HcHardwareCon
fi
guration
–
DREQ1 output polarity (bit 5)
–
DACK1 input polarity (bit 6)
–
DACK mode (bit 8).
Hc
μ
PInterruptEnable
–
If you want an interrupt to be generated after the DMA transfer is complete, set
EOTInterruptEnable (bit 3).
Table 6:
Addressing mode
[1]
Direct addressing
Indirect addressing
Registers used in addressing modes
HcDMACon
fi
guration bit[3:1]
1XXB
0XXB
Total bytes to transfer
HcDirectAddressLength
HcTransferCounter
相關PDF資料
PDF描述
ISP1362BD Single-chip Universal Serial Bus On-The-Go controller
ISP1362EE Single-chip Universal Serial Bus On-The-Go controller
ISP1501 Hi-Speed Universal Serial Bus peripheral transceiver
ISP1520 Hi-Speed Universal Serial Bus hub controller
ISP1520BD Hi-Speed Universal Serial Bus hub controller
相關代理商/技術參數
參數描述
ISP1362BD 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,118 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,151 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,157 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD157 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB-OTG 64LQFP 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 64-LQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*