參數資料
型號: EP7209
廠商: Cirrus Logic, Inc.
英文描述: Ultra-Low-Power Audio Decoder System-on-Chip
中文描述: 超低功耗音頻解碼器系統級芯片
文件頁數: 57/128頁
文件大?。?/td> 1382K
代理商: EP7209
EP7209
DS453PP2
57
9
BZTOG
: Bit to drive (i.e., toggle) the buzzer output directly when software mode of operation is
selected (i.e., bit BZMOD = 0). See the BZMOD and BUZFREQ (SYSCON1) bits for more
details.
BZMOD
: This bit selects the buzzer drive mode. When BZMOD = 0, the buzzer drive output pin
is connected directly to the BZTOG bit. This is the software mode. When BZMOD = 1, the buzzer
drive is in the hardware mode. Two hardware sources are available to drive the pin. They are the
TC1 or a fixed internally generated clock source. The selection of which source is used to drive
the pin is determined by the state of the BUZFREQ bit in the SYSCON2 register. If the TC1 is
selected, then the buzzer output pin is connected to the TC1 under flow bit. The buzzer output
pin changes every time the timer wraps around. The frequency depends on what was pro-
grammed into the timer. See the description of the BUZFREQ and BZTOG bits (SYSCON2) for
more details.
DBGEN
: Setting this bit will enable the debug mode. In this mode, all internal accesses are out-
put as if they were reads or writes to the expansion memory addressed by nCS5. nCS5 will still
be active in its standard address range. In addition the internal interrupt request and fast interrupt
request signals to the ARM720T processor are output on Port E, bits 1 and 2. Note that these bits
must be programmed to be outputs before this functionality can be observed. The clock to the
CPU is output on Port E, Bit 0 to enable individual accesses to be distinguished. For example, in
debug mode:
nCS5 = nCS5 or internal I/O strobe
PE0 = CLK
PE1 = nIRQ
PE2 = nFIQ
LCDEN
: LCD enable bit. Setting this bit enables the LCD controller.
10
11
12
13
CDENTX
: Codec interface enable TX bit. Setting this bit enables the codec interface for data
transmission to an external codec device.
CDENRX
: Codec interface enable RX bit. Setting this bit enables the codec interface for data
reception from an external codec device.
NOTE:
Both CDENRX and CDENTX need to be enabled/disabled in tandem, otherwise data may
be lost.
SIREN
: HP SIR protocol encoding enable bit. This bit will have no effect if the UART is not
enabled.
ADCKSEL
: Microwire / SPI peripheral clock speed select. This two bit field selects the frequency
of the ADC sample clock; this is twice the frequency of the synchronous serial ADC interface
clock. The table below shows the available frequencies for operation when in PLL mode. These
bits are also used to select the shift clock frequency for the SSI2 interface when set into master
mode. The frequencies obtained in 13.0 MHz mode can be found in
Table 21
.
14
15
16:17
Bit
Description
Table 27. SYSCON1
(cont.)
ADCKSEL
ADC Sample Frequency
(kHz)
SMPCLK
8
32
128
256
ADC Clock Frequency
(kHz)
ADCCLK
4
16
64
128
00
01
10
11
相關PDF資料
PDF描述
EP7211 HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7211-CP-A HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7211-CV-A HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7212 HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CB-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
相關代理商/技術參數
參數描述
EP7209-CB-D 制造商:Rochester Electronics LLC 功能描述:- Bulk
EP7209-CV-D 制造商:Rochester Electronics LLC 功能描述:- Bulk
EP7211 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7211(208LQFP) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC
EP7211(256PBGA) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC