參數資料
型號： ENC624J600T-I/PT
廠商： Microchip Technology
文件頁數： 146/168頁
文件大?。?/td> 0K
描述： IC ETHERNET CTRLR W/SPI 64-TQFP
視頻文件： Fast 100 Mbps Ethernet PICtail Plus Overview
標準包裝： 1,200
控制器類型： 以太網控制器（IEEE 802.3）
接口： SPI
電源電壓： 3 V ~ 3.6 V
電流 - 電源： 96mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-TQFP
供應商設備封裝： 64-TQFP（10x10）
包裝： 帶卷 (TR)
配用： AC164132-ND - BOARD DAUGHTER PICTAIL ETHERNET
2007 Microchip Technology Inc.
DS39599G-page 77
PIC18F2220/2320/4220/4320
6.5
Writing to Flash Program Memory
The programming block size is 4 words or 8 bytes.
Word or byte programming is not supported.
Table writes are used internally to load the holding reg-
isters needed to program the Flash memory. There are
8 holding registers used by the table writes for
programming.
Since the Table Latch (TABLAT) is only a single byte,
the TBLWT instruction has to be executed 8 times for
each programming operation. All of the table write
operations will essentially be short writes because only
the holding registers are written. At the end of updating
8 registers, the EECON1 register must be written to, to
start the programming operation with a long write.
The long write is necessary for programming the inter-
nal Flash. Instruction execution is halted while in a long
write cycle. The long write will be terminated by the
internal programming timer.
FIGURE 6-5:
TABLE WRITES TO FLASH PROGRAM MEMORY
6.5.1
FLASH PROGRAM MEMORY WRITE
SEQUENCE
The sequence of events for programming an internal
program memory location should be:
1.
Read 64 bytes into RAM.
2.
Update data values in RAM as necessary.
3.
Load Table Pointer with address being erased.
4.
Do the row erase procedure (see Section 6.4.1
5.
Load Table Pointer with address of first byte
being written.
6.
Write the first 8 bytes into the holding registers
with auto-increment.
7.
Set the EECON1 register for the write operation:
set EEPGD bit to point to program
memory;
clear the CFGS bit to access program
memory;
set WREN bit to enable byte writes.
8.
Disable interrupts.
9.
Write 55h to EECON2.
10. Write AAh to EECON2.
11. Set the WR bit. This will begin the write cycle.
12. The CPU will stall for duration of the write (about
2 ms using internal timer).
13. Execute a NOP.
14. Re-enable interrupts.
15. Repeat steps 6-14 seven times, to write 64
bytes.
16. Verify the memory (table read).
This procedure will require about 18 ms to update one
row of 64 bytes of memory. An example of the required
code is given in Example 6-3.
Holding Register
TABLAT
Holding Register
TBLPTR = xxxxx7
Holding Register
TBLPTR = xxxxx1
Holding Register
TBLPTR = xxxxx0
8
Write Register
TBLPTR = xxxxx2
Program Memory
相關PDF資料
PDF描述
EP1AGX90EF1152I6 IC ARRIA GX FPGA 90K 1152FBGA
EP1C3T144A8N IC CYCLONE FPGA 2910 LE 144-TQFP
EP1K100FC484-1N IC ACEX 1K FPGA 100K 484-FBGA
EP1S80F1020C5N IC STRATIX FPGA 80K LE 1020-FBGA
EP1SGX40GF1020I6 IC STRATIX GX FPGA 40K 1020-FBGA
相關代理商/技術參數
參數描述
ENC680D05B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
ENC680D-05B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STD MOV
ENC680D07B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
ENC680D-07B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STD MOV
ENC680D10B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*