- 您現在的位置：買賣IC網 > PDF目錄379184 > DS80CH11 System Energy Manager PDF資料下載
參數資料
| 型號： | DS80CH11 |
| 英文描述： | System Energy Manager |
| 中文描述： | 系統能量管理器 |
| 文件頁數： | 43/88頁 |
| 文件大?。?/td> | 598K |
| 代理商： | DS80CH11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
DS80CH11
011200 43/88
6.3.5
The bus monitor mode is provided to allow the SEM to
“l(fā)isten” as a third party to conversations between exter-
nal master and slave devices. This mode can be useful
for diagnostic purposes, or to help the system recover
from a detected error condition.
Bus Monitor Mode Operation
When the BMMx bit is set to 1, bus monitoring is
enabled. In this mode the port will generate an interrupt
for every action on the bus even when it is not operating
as a master or being addressed as a slave. As a result,
when a transfer takes place between an external master
and slave, the port will be notified of a transmitted
START condition, will receive the subsequent address
and data bytes on the bus, and will finally be notified of a
transmitted STOP condition.
If the SEM is receiving a transfer between an external
master and an external slave device, the timing is nearly
identical to that for Slave Receive operation as shown in
Figure 6–6. The exceptions to this timing are summa-
rized as follows: 1) An additional interrupt will be gener-
ated when a Receive START condition is detected as
indicated by RSTAx = 1. This will inform the firmware of
the start of a message and allow it to identify the next
byte as an address. 2) A positive acknowledge pulse
will never be generated. 3) SCLx will never be held low
to prevent data in the receive buffer from being overwrit-
ten. Other than these differences bytes are received
and all other status is flagged as described for Slave
Receiver operation.
When BMMx = 1 and the SEM is operating as a master
or is being addressed as a slave, the Master Transmit,
Master Receive, Slave Transmit, and Slave Receive
modes will all operate exactly as documented above
with the exception that RSTAx becomes an additional
interrupt flag that is set whenever a START condition is
detected on the bus.
When BMMx = 0, bus monitoring is disabled and inter-
rupt flags are only generated when the port is operating
as a master or being addressed as a slave device.
Transfers between external devices are ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| DS83C520 | EPROM/ROM High-Speed Micro |
| DS83C520-ECL | EPROM/ROM High-Speed Micro |
| DS83C520-ENL | EPROM/ROM High-Speed Micro |
| DS83C520-MCL | EPROM/ROM High-Speed Micro |
| DS83C520-MNL | EPROM/ROM High-Speed Micro |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80CH11+E02 | 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11+E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11+E02 System Energy Managers |
| DS80CH11-E02 | 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11-E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11-E02 System Energy Managers |
| DS80E100 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables |
| DS80EP100 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables |
| DS80EP100_08 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables |
發布緊急采購，3分鐘左右您將得到回復。