- 您現在的位置：買賣IC網 > PDF目錄298840 > ATA6285N-PNPW (ATMEL CORP) SPECIALTY TELECOM CIRCUIT, QCC32 PDF資料下載
參數資料
| 型號： | ATA6285N-PNPW |
| 廠商： | ATMEL CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | SPECIALTY TELECOM CIRCUIT, QCC32 |
| 封裝： | 5 X 5MM, QFN-32 |
| 文件頁數： | 31/121頁 |
| 文件大?。?/td> | 9917K |
| 代理商： | ATA6285N-PNPW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁
17
4958B–AUTO–11/10
Atmel ATA6285/ATA6286 [Preliminary]
3.5.7
Reset and Interrupt Handling
The Atmel
AVR provides several different interrupt sources. These interrupts and the sepa-
rate Reset Vector each have a separate program vector in the program memory space. All
interrupts are assigned individual enable bits which must be written logic one together with the
Global Interrupt Enable bit in the Status Register in order to enable the interrupt. Depending on
the Program Counter value, interrupts may be automatically disabled when Boot Lock bits
BLB02 or BLB12 are programmed. This feature improves software security. See Section
details.
The lowest addresses in the program memory space are by default defined as the Reset and
Interrupt Vectors. The complete list of vectors is shown in Section 3.10 “Interrupts” on page 47.
The list also determines the priority levels of the different interrupts. The lower the address the
higher is the priority level. RESET has the highest priority, and next is INT0 - the External Inter-
rupt Request 0. The Interrupt Vectors can be moved to the start of the Boot Flash section by
setting the IVSEL bit in the MCU Control Register (MCUCR). Refer to Section 3.10 “Interrupts”
on page 47 for more information. The Reset Vector can also be moved to the start of the Boot
Flash section by programming the BOOTRST Fuse, see Section 3.19 “Boot Loader Support -
When an interrupt occurs, the Global Interrupt Enable I-bit is cleared and all interrupts are dis-
abled. The user software can write logic one to the I-bit to enable nested interrupts. All enabled
interrupts can then interrupt the current interrupt routine. I-bit is automatically set when a Return
from Interrupt instruction - RETI - is executed.
There are basically two types of interrupts. The first type is triggered by an event that sets the
Interrupt Flag. For these interrupts, the Program Counter is vectored to the actual Interrupt Vec-
tor in order to execute the interrupt handling routine, and hardware clears the corresponding
Interrupt Flag. Interrupt Flags can also be cleared by writing a logic one to the flag bit position(s)
to be cleared. If an interrupt condition occurs while the corresponding interrupt enable bit is
cleared, the Interrupt Flag will be set and remembered until the interrupt is enabled, or the flag is
cleared by software. Similarly, if one or more interrupt conditions occur while the Global Interrupt
Enable bit is cleared, the corresponding Interrupt Flag(s) will be set and remembered until the
Global Interrupt Enable bit is set, and will then be executed by order of priority.
The second type of interrupts will trigger as long as the interrupt condition is present. These
interrupts do not necessarily have Interrupt Flags. If the interrupt condition disappears before the
interrupt is enabled, the interrupt will not be triggered.
When the Atmel AVR exits from an interrupt, it will always return to the main program and exe-
cute one more instruction before any pending interrupt is served.
Note that the Status Register is not automatically stored when entering an interrupt routine, and
not restored when returning from an interrupt routine. This must be handled by software.
When using the CLI instruction to disable interrupts, the interrupts will be immediately disabled.
No interrupt will be executed after the CLI instruction, even if it occurs simultaneously with the
CLI instruction. The following example shows how this can be used to avoid interrupts during the
timed EEPROM write sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| ATA6285N-PNQW | SPECIALTY TELECOM CIRCUIT, QCC32 |
| ATCB-B01-RM50 | INTERCONNECTION DEVICE |
| ATEP-161100-SMA-P-01 | INTERCONNECTION DEVICE |
| ATH15T05-9S | 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
| ATO2815T | 3-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATA6285N-PNQW | 功能描述:射頻微控制器 - MCU IC LF, Cap. Sens. Interface RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:Si100x 數據總線寬度:8 bit 最大時鐘頻率:24 MHz 程序存儲器大小:64 KB 數據 RAM 大小:4 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LGA-42 安裝風格:SMD/SMT 封裝:Tube |
| ATA6285-PNPW | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:TPMS Control and Transmitter IC |
| ATA6285-PNQW | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:TPMS Control and Transmitter IC |
| ATA6286 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:TPMS Control and Transmitter IC |
| ATA6286C-PNPW | 制造商:Atmel Corporation 功能描述:IC CTLR/XMITTER 433MHZ 32QFN 制造商:Atmel Corporation 功能描述:Active RFID AVR-uC, 125kHz + 433MHz |
發布緊急采購，3分鐘左右您將得到回復。