參數資料
型號: ATA6285N-PNPW
廠商: ATMEL CORP
元件分類: 通信及網絡
英文描述: SPECIALTY TELECOM CIRCUIT, QCC32
封裝: 5 X 5MM, QFN-32
文件頁數: 27/121頁
文件大?。?/td> 9917K
代理商: ATA6285N-PNPW
13
4958B–AUTO–11/10
Atmel ATA6285/ATA6286 [Preliminary]
3.5.3
Status Register
The Status Register contains information about the result of the most recently executed arithme-
tic instruction. This information can be used for altering program flow in order to perform
conditional operations. Note that the Status Register is updated after all ALU operations, as
specified in the Instruction Set Reference. This will in many cases remove the need for using the
dedicated compare instructions, resulting in faster and more compact code. The Status Register
is not automatically stored when entering an interrupt routine and restored when returning from
an interrupt. This must be handled by software.
3.5.3.1
The Atmel AVR Status REGister - SREG - :
Bit 7 - I: Global Interrupt Enable
The Global Interrupt Enable bit must be set for the interrupts to be enabled. The individual inter-
rupt enable control is then performed in separate control registers. If the Global Interrupt Enable
Register is cleared, none of the interrupts are enabled independent of the individual interrupt
enable settings. The I-bit is cleared by hardware after an interrupt has occurred, and is set by
the RETI instruction to enable subsequent interrupts. The I- bit can also be set and cleared by
the application with the SEI and CLI instructions, as described in the instruction set reference.
Bit 6 - T: Bit Copy Storage
The Bit Copy instructions BLD (Bit LoaD) and BST (Bit STore) use the T-bit as source or desti-
nation for the operated bit. A bit from a register in the Register File can be copied into T by the
BST instruction, and a bit in T can be copied into a bit in a register in the Register File by the
BLD instruction.
Bit 5 - H: Half Carry Flag
The Half Carry Flag H indicates a Half Carry in some arithmetic operations. Half Carry is useful
information.
Bit 4 - S: Sign Bit, S = N
V
The S-bit is always an exclusive or between the Negative Flag N and the Two's Complement
information.
Bit 3 - V: Two's Complement Overflow Flag
The Two's Complement Overflow Flag V supports two's complement arithmetic. See Section
Bit 2 - N: Negative Flag
The Negative Flag N indicates a negative result in an arithmetic or logic operation. See Section
Bit
7
654
321
0
I
T
H
S
V
N
Z
CSREG
Read/Write
R/W
Initial Value
0
000
0
相關PDF資料
PDF描述
ATA6285N-PNQW SPECIALTY TELECOM CIRCUIT, QCC32
ATCB-B01-RM50 INTERCONNECTION DEVICE
ATEP-161100-SMA-P-01 INTERCONNECTION DEVICE
ATH15T05-9S 1-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE
ATO2815T 3-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
ATA6285N-PNQW 功能描述:射頻微控制器 - MCU IC LF, Cap. Sens. Interface RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:Si100x 數據總線寬度:8 bit 最大時鐘頻率:24 MHz 程序存儲器大小:64 KB 數據 RAM 大小:4 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LGA-42 安裝風格:SMD/SMT 封裝:Tube
ATA6285-PNPW 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:TPMS Control and Transmitter IC
ATA6285-PNQW 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:TPMS Control and Transmitter IC
ATA6286 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:TPMS Control and Transmitter IC
ATA6286C-PNPW 制造商:Atmel Corporation 功能描述:IC CTLR/XMITTER 433MHZ 32QFN 制造商:Atmel Corporation 功能描述:Active RFID AVR-uC, 125kHz + 433MHz