參數資料
型號： AD1801
廠商： Analog Devices, Inc.
英文描述： Single-Chip Fax/Data/ Voice Modem(單片的傳真/數據/語音調制解調器)
中文描述： 單芯片傳真/數據/語音調制解調器（單片的傳真/數據/語音調制解調器）
文件頁數： 30/52頁
文件大小： 348K
代理商： AD1801
AD1801
–30–
REV. 0
SigChg
Signal Change Enable/Disable. This bit is set and reset by the host to enable and disable a status change signal
from the status register. When this bit is set, and the card is configured for the I/O interface, the Chng bit controls
Pin 92 (
CHG
). If no status change signal is desired, the bit should be set to zero and the
CHG
signal will be held
deasserted when the card is configured for I/O.
In the AD1801, SigChg is “0” for Function 1.
I/O cycles occur only as 8-bit transfers. When the host can provide I/O cycles only using the SD7:SD0 data path,
the PCMCIA software will set this bit to a 1. The card is guaranteed that accesses to 16-bit registers will occur as two
byte accesses rather than a single 16-bit access. This information is useful when 16-bit and 8-bit registers overlap.
On the AD1801, this bit is hardcoded to “0” (16-bit transfers allowed).
Reserved bits must be 0.
Audio Enable. This bit enables audio information to be sent to the Host Bus Adapter via the speaker pin
SPKR
(Pin 91) when configured for an I/O interface.
In the AD1801, Audio is “0” for Function 1.
Power-Down. This bit is set to one to request that Function 1 enter a power-down state. PCMCIA software must
not place Function 1 into a power-down state while the Function’s READY pin is in the LO (busy) state.
Interrupt Request Pending. This bit represents the internal state of the interrupt request. This value is available
whether or not interrupts have been configured. How the Intr bit is cleared is dependent up on how the IntrAck
bit is configured.
IntrAck = 0—Intr reflects the function’s interrupt request status. If the interrupt is cleared within the function,
then Intr is reset by the function.
IntrAck = 1—Intr remains set even though the interrupt condition has been cleared (i.e., sticky). It is reset by
system software to indicate it is ready to receive another interrupt (implemented to support interrupt sharing).
Interrupt Acknowledge. This bit determines the response of the Intr bit. The functionality associated with the
IntrAck bit permits two or more functions to share the PC Card’s
IREQ
pin.
IntrAck = 0—When IntrAck is reset, Intr functions as described above to support a single interrupt implementation.
IntrAck = 1—This causes the Intr bit to remain set even though the interrupt service routine has already serviced
the interrupt. Normally, the interrupt service routine clears the interrupt pending bit in a function specific regis-
ter, causing the Intr also to be cleared; however, to support interrupt sharing, the Intr bit is not cleared until PC-
MCIA specific software is ready to handle the next interrupt request. When cleared by the PCMCIA software,
other interrupt requests that are pending can now be asserted over the PC Card’s
IREQ
pin.
CSR2: PCMCIA Function 2 Configuration and Status Register
IOis8
Res
Audio
PwrDn
Intr
IntrAck
Access: Read/Write
Address: 0x442
7
a
t
a
D
6
a
t
a
D
5
a
t
a
D
4
a
t
a
D
3
a
t
a
D
2
a
t
a
D
1
a
t
a
D
0
a
t
a
D
g
n
h
C
g
h
C
g
S
8
s
O
I
)
0
(
e
R
o
i
d
u
A
n
D
r
w
P
r
n
I
k
c
A
r
n
I
Chng
Status Change Detected. This bit indicates that one or more of the Pin Replacement register bits (CBVD1,
CBVD2, CRDY or CWProt) is set to one, normally causing the
CHG
signal (Pin 92) to be asserted. However, if
the SigChg bit (see below) is “1” and the card is configured for an I/O interface, the
CHG
pin is asserted when
this bit is set.
In the AD1801, Chng is “0” for Function 2.
Signal Change Enable/Disable. This bit is set and reset by the host to enable and disable a status change signal
from the status register. When this bit is set and the card is configured for the I/O interface, the Chng bit controls
Pin 92 (
CHG
). If no status change signal is desired, the bit should be set to zero and the
CHG
signal will be held
deasserted when the card is configured for I/O.
In the AD1801, SigChg is “0” for Function 2.
I/O Cycles Occur Only as 8-Bit Transfers. When the host can provide I/O cycles using only the SD7:SD0 data
path, the PCMCIA software will set this bit to a 1. The card is guaranteed that accesses to 16-bit registers will
occur as two byte accesses rather than a single 16-bit access. This information is useful when 16-bit and 8-bit
registers overlap.
On the AD1801, this bit is hardcoded to “0” (16-bit transfers allowed).
Reserved bits must be 0.
Audio Enable. This bit enables audio information to be sent to the Host Bus Adapter via the speaker pin
SPKR
(Pin 91) when configured for an I/O interface.
In the AD1801, Audio is “0” for Function 2.
SigChg
IOis8
Res
Audio
相關PDF資料
PDF描述
AD1803JRU U.S./International Modem DAA Line Codec Chipset
AD1803 ECONOLINE: RD & RC - Dual Output from a Single Input Rail- 1kVDC & 2kVDC Isolation- Power Sharing on Output- Custom Solutions Available- UL94V-0 Package Material- Efficiency to 86%
AD1804 U.S./International Modem DAA Line Codec Chipset
AD1804JRU ECONOLINE: RD & RC - Dual Output from a Single Input Rail- 1kVDC & 2kVDC Isolation- Power Sharing on Output- Custom Solutions Available- UL94V-0 Package Material- Efficiency to 86%
AD1812JST Silver Mica Capacitor; Capacitance:12pF; Capacitance Tolerance: 5%; Series:CD17; Voltage Rating:500VDC; Capacitor Dielectric Material:Mica; Termination:Radial Leaded; Lead Pitch:5.9mm; Leaded Process Compatible:No RoHS Compliant: No
相關代理商/技術參數
參數描述
AD1801JS 制造商:Rochester Electronics LLC 功能描述:- Bulk
AD1801JST-REEL 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
AD1803 制造商:AD 制造商全稱:Analog Devices 功能描述:U.S./International Modem DAA Line Codec Chipset
AD1803-0.4 制造商:Analog Devices 功能描述:
AD1803JRU 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*