參數資料
型號： 8XC196LX
英文描述： 8XC196Lx - 8XC196Lx Supplement to 8X196Kx. 8X196Jx. 87C196CA User＇s Manual
中文描述： 8XC196Lx - 8XC196Lx補編8X196Kx。 8X196Jx。 87C196CA用戶手冊
文件頁數： 83/136頁
文件大?。?/td> 659K
代理商： 8XC196LX
8-17
J1850 COMMUNICATIONS CONTROLLER
J_CMD
Address:
Reset State:
1F51H
00H
The J1850 command (J_CMD) register determines the messaging type, specifies the number of bytes
to be transmitted in the next message frame, and updates the status of the message transmission in
progress. This byte register can be directly addressed through windowing You must write to this
register prior to transmitting every message.
7
0
AUTO
IFR
IGNORE
ABORT
MSG3
MSG2
MSG1
MSG0
Bit
Number
Bit
Mnemonic
Function
7
AUTO
Automatic Transmit Retry
This bit, when arbitration is lost on the first byte of your message, prompts
the transmitter to automatically retry until the byte is successfully
transmitted. Automatic retry applies only to the first byte.
0 = normal operation
1 = enable automatic retry
6
IFR
In-frame Response Indicator
This bit signals that a normalization bit (NB) is to be sent after an end-of-
data symbol is detected on the bus and that the subsequent byte written to
the J1850 transmitter (J_TX) register is an in-frame response (IFR).
0 = standard messaging
1 = next byte written to J_TX is an IFR
5
IGNORE
Ignore Incoming Message
This bit instructs the bus to ignore the incoming message until an EOF
symbol is detected. The bit is cleared after an EOF symbol is detected.
0 = normal operation
1 = ignore incoming message
4
ABORT
Abort Transmission
This bit aborts any transmission in progress and flushes the transmit buffer
(JTX_BUF). To prevent another node from mistakenly assuming that the
last byte was a CRC byte, two extra ‘1’s are appended.
0 = normal operation
1 = abort transmission in progress
3:0
MSG3:0
Message
These four bits specify the number of bytes to be transmitted in the next
message frame. This number includes the header, but not the CRC byte. In
normal messaging, the maximum number of bytes you can transmit in a
message frame is eleven.
MSG3:0
Operation
Purpose
FH
Termination byte
Terminate block transmission
EH
Block transmission Transmit unspecified number of bytes
DH
Reserved
—
CH
Reserved
—
B:0H
Normal messaging Transmit specified number of bytes
Figure 8-16. J1850 Command (J_CMD) Register
相關PDF資料
PDF描述
8XC51FA 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51FC 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51RD 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC80C32 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51FB Low power single card reader
相關代理商/技術參數
參數描述
8XC196MC 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:INDUSTRIAL MOTOR CONTROL MICROCONTROLLER
8XC196MD 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:INDUSTRIAL MOTOR CONTROL MICROCONTROLLER
8XC196MH 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:8XC196MH INDUSTRIAL MOTOR CONTROL CHMOS MICROCONTROLLER
8XC196NP 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:COMMERCIAL CHMOS 16-BIT MICROCONTROLLER
8XC196NT 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS MICROCONTROLLER WITH 1 MBYTE LINEAR ADDRESS SPACE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*