參數資料
型號: 8XC196LX
英文描述: 8XC196Lx - 8XC196Lx Supplement to 8X196Kx. 8X196Jx. 87C196CA User's Manual
中文描述: 8XC196Lx - 8XC196Lx補編8X196Kx。 8X196Jx。 87C196CA用戶手冊
文件頁數: 78/136頁
文件大小: 659K
代理商: 8XC196LX
8XC196LXSUPPLEMENT
8-12
8.4.2
In-frame Response Messaging
There are three types of in-frame response (IFR) message framings: type 1 (a single byte from a
single responder), type 2 (a single byte from multiple responders), and type 3 (multiple bytes from
a single responder). Like the standard message frame, the IFR frame is composed of header, data,
and CRC bytes, and a series of start and end symbols. Unlike the standard message frame, the
actual length of the IFR message frame will differ based on the desired response.
Consider the following example: a system’s controller (the requestor) requests an information up-
date from each of four nodes (the responders) in the system. With type 1 messaging, the controller
can receive a limited information update if it sends out four separate transmissions. With type 2
messaging, the controller can receive a limited information update by sending one message. With
type 3 messaging, the controller can receive unlimited information; however, it will require four
separate transmissions. The following subsections detail this example for the three IFR messag-
ing types.
8.4.2.1
IFR Messaging Type 1: Single Byte, Single Responder
No IFR messaging type carries a distinct advantage or disadvantage over the other messaging
types. IFR messaging type 1 (Figure 8-9) is ideal for use when requesting small amounts of in-
formation from a single source in your system. In the above example, suppose you want to know
how many pounds of pressure each of the four remote node sites experienced after the controller
sent out a request to each node sensor to exert a given amount of pressure. If you use type 1 mes-
saging, the controller will send four separate serial messages to the remote node sites in the sys-
tem and wait for their responses. Keeping the data timing a constant, the CPU overhead of
transmitting these messages alone amounts to a minimum of 4.96 ms (refer to Table 8-4 on page
8-11 for all symbol timings).
Figure 8-9. IFR Type 1 Message Frame
8.4.2.2
IFR Messaging Type 2: Single Byte, Multiple Responders
When response time is the highest consideration, IFR messaging type 2 is desirable. IFR type 2
messaging can monitor up to 32 remote nodes on a given request (see Figure 8-10). While it al-
lows only one byte of information per response, in many cases a single byte of information is
more than adequate. In our example, suppose that each node sensor detected a pressure of 75
P.S.I. (pounds per square inch). The response (the value 75) would take a single byte, 46H, to
communicate the reply. The maximum overhead required is 1.24 ms, or one fourth the time it
would take type 1 messaging to achieve the same results.
A5229-01
0-1 Byte
CRC
E
O
D
S
O
F
E
O
F
I
F
S
The number of data bytes to be transferred is unspecified if 0EH is written to J_CMD3:0.
1Byte
IFR Data
1 Byte
CRC
E
O
D
N
B
1-3 Bytes
Header
1-11 Bytes
Data
In-frame Response (IFR) Frame
相關PDF資料
PDF描述
8XC51FA 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51FC 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51RD 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC80C32 8-bit CMOS (low voltage, low power and high speed) microcontroller families
8XC51FB Low power single card reader
相關代理商/技術參數
參數描述
8XC196MC 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:INDUSTRIAL MOTOR CONTROL MICROCONTROLLER
8XC196MD 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:INDUSTRIAL MOTOR CONTROL MICROCONTROLLER
8XC196MH 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:8XC196MH INDUSTRIAL MOTOR CONTROL CHMOS MICROCONTROLLER
8XC196NP 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:COMMERCIAL CHMOS 16-BIT MICROCONTROLLER
8XC196NT 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS MICROCONTROLLER WITH 1 MBYTE LINEAR ADDRESS SPACE