- 您現在的位置：買賣IC網 > PDF目錄69028 > MCC68HC711D3 (MOTOROLA INC) 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC PDF資料下載
參數資料
| 型號： | MCC68HC711D3 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, UUC |
| 封裝： | DIE |
| 文件頁數： | 131/157頁 |
| 文件大?。?/td> | 2252K |
| 代理商： | MCC68HC711D3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁當前第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
Serial Communications Interface (SCI)
Receive Operation
MC68HC711D3 — Rev. 2
Data Sheet
MOTOROLA
Serial Communications Interface (SCI)
75
6.4 Receive Operation
During receive operations, the transmit sequence is reversed. The serial shift
register receives data and transfers it to a parallel receive data register (SCDR) as
a complete word. Refer to Figure 6-2. This double-buffered operation allows a
character to be shifted in serially while another character is already in the SCDR.
An advanced data recovery scheme distinguishes valid data from noise in the
serial data stream. The data input is selectively sampled to detect receive data, and
a majority voting circuit determines the value and integrity of each bit.
6.5 Wakeup Feature
The wakeup feature reduces SCI service overhead in multiple receiver systems.
Software for each receiver evaluates the first character of each message. The
receiver is placed in wakeup mode by writing a 1 to the RWU bit in the SCCR2
register. While RWU is 1, all of the receiver-related status flags (RDRF, IDLE, OR,
NF, and FE) are inhibited (cannot become set). Although RWU can be cleared by
a software write to SCCR2, to do so would be unusual. Normally, RWU is set by
software and is cleared automatically with hardware. Whenever a new message
begins, logic alerts the sleeping receivers to wake up and evaluate the initial
character of the new message.
Two methods of wakeup are available:
Idle line wakeup
Address mark wakeup
During idle line wakeup, a sleeping receiver awakens as soon as the RxD line
becomes idle. In the address mark wakeup, logic 1 in the most significant bit (MSB)
of a character wakes up all sleeping receivers.
6.5.1 Idle-Line Wakeup
To use the receiver wakeup method, establish a software addressing scheme to
allow the transmitting devices to direct a message to individual receivers or to
groups of receivers. This addressing scheme can take any form as long as all
transmitting and receiving devices are programmed to understand the same
scheme. Because the addressing information is usually the first frame(s) in a
message, receivers that are not part of the current task do not become burdened
with the entire set of addressing frames. All receivers are awake (RWU = 0) when
each message begins. As soon as a receiver determines that the message is not
intended for it, software sets the RWU bit (RWU = 1), which inhibits further flag
setting until the RxD line goes idle at the end of the message. As soon as an idle
line is detected by receiver logic, hardware automatically clears the RWU bit so that
the first frame of the next message can be received. This type of receiver wakeup
requires a minimum of one idle-line frame time between messages and no idle time
between frames in a message.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC711D3MP2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC711D3S | 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER, CDIP40 |
| MC68HC711D3FN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC711G5CFN | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
| MC68HC11G7CFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCC68HRC705JP7 | 制造商:Motorola Inc 功能描述: |
| MCC6M10 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M10 STUD |
| MCC6M3 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM M3 STUD |
| MCC6M3.5 | 制造商:Thomas & Betts 功能描述:METRIC CU CONNECTOR 6SQMM 3.5 STUD |
| MCC6M4 | 制造商:Thomas & Betts 功能描述:METRIC CONNECTOR 6SQMM M4 STUD |
發布緊急采購，3分鐘左右您將得到回復。