參數資料
型號: MC92603VF
廠商: Freescale Semiconductor
文件頁數: 64/126頁
文件大?。?/td> 0K
描述: IC TXRX ETH QUAD GIG 256-MAPBGA
標準包裝: 1
類型: 收發器
驅動器/接收器數: 4/4
規程: 千兆位以太網
電源電壓: 4.5 V ~ 5.5 V
安裝類型: 表面貼裝
封裝/外殼: 256-LBGA
供應商設備封裝: 256-MAPBGA
包裝: 托盤
Receiver
MC92603 Quad Gigabit Ethernet Transceiver Reference Manual, Rev. 1
3-8
Freescale Semiconductor
internal 8B/10B decoder was used to decode data from the received 10-bit character. Byte interface mode
is enabled by negating TBIE low.
Received data is 10-bits of pre-coded data when in the 10-bit interface, TBI, mode. The internal 8B/10B
decoder is not used, and it is assumed that decoding is done externally. The 10-bit interface mode is
enabled by asserting TBIE high.
The received data is presented on the interface RECV_x_7 through RECV_x_0 signals when operating in
the GMII or 8-bit backplane modes. In the 10-bit backplane or TBI modes, RECV_x_ERR, RECV_x_DV
become bits 9 and 8, respectively.
In the reduced interface operational modes, the receiver signals RECV_x_7 through RECV_x_4 are not
used and the 5th and 9th data bits are output on the RECV_x_DV signal. With the reduced interface, data
in the alignment FIFO is presented at the receiver interface as double data rate (DDR), on the rising and
falling edge of the appropriate receiver clock, RECV_x_RCLK.
The receiver status and error reporting is coded onto the RECV_x_ERR, RECV_x_DV,
RECV_x_COMMA, and RECV_x_K signals.
All of the digital outputs of the device are internally “source terminated” and therefore do not require
exernal series resistors on the pcb. This applies to all received data, status, and clock outputs on the
MC92603.
3.5
Data Alignment Configurations
The receiver supports two modes of byte alignment as defined by the BSYNC signal. Table 3-5 shows the
settings to activate each mode.
NOTE
Do not use non-aligned mode (BSYNC = low) in 8-bit modes. The
non-aligned mode is only valid if TBIE is high.
3.5.1
Non-Aligned Mode (BSYNC = Low)
In non-aligned mode no attempt is made to align the incoming data stream. The bits are simply
accumulated into 10-bit code groups and forwarded. This mode should be used only with backplane 10-
or 5-bit data mode (TBIE = high, COMPAT = low), and with word synchronization disabled
(WSYNC1 = low and WSYNC0 = low).
3.5.2
Byte-Aligned Mode (BSYNC = High)
The remaining 4 receiver operating modes, shown in Table 3-4 align the incoming serial data into 10-bit
code groups. At power up, the receiver starts an alignment procedure, searching for the 8-bit pattern
Table 3-5. Byte Synchronization Modes
Byte Alignment Mode
BSYNC
Byte Aligned
High
Non-Aligned
Low
相關PDF資料
PDF描述
MC92604VM IC ETH TXRX DUAL GIG 196-MAPBGA
MC92604ZT IC TXRX ETH DUAL GIG 196-MAPBGA
MCP2120T-I/SL IC ENCODR/DECODR 2.5V IR 14-SOIC
MCP2122-E/P IC ENCODER/DECODER IRDA 8-DIP
MCP2122T-E/SNG IC ENCODER/DECODR INFRARED 8SOIC
相關代理商/技術參數
參數描述
MC92603VM 功能描述:IC ETH TXRX QUAD GIG 256-MAPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC92604VM 功能描述:IC ETH TXRX DUAL GIG 196-MAPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC92604ZT 功能描述:IC TXRX ETH DUAL GIG 196-MAPBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP(0.300",7.62mm) 供應商設備封裝:16-PDIP 包裝:管件
MC92610 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Quad 3.125 Gbaud SERDES
MC92610VF 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Quad 3.125 Gbaud SERDES