參數資料
型號: ISP1760
廠商: NXP Semiconductors N.V.
英文描述: Hi-Speed Universal Serial Bus host controller for embedded applications
中文描述: 高速嵌入式應用的通用串行總線主控制器
文件頁數: 21/105頁
文件大?。?/td> 449K
代理商: ISP1760
9397 750 13257
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 01 — 8 November 2004
21 of 105
Philips Semiconductors
ISP1760
Embedded Hi-Speed USB host controller
With the help of the IRQ Mask AND and IRQ Mask OR registers for each type of
transfer—ISO, INT and bulk—software can determine which PTDs get priority and an
interrupt will be generated when the AND or OR conditions are met. The PTDs that are
set will wait until the respective bits of the remaining PTDs are set and then all PTDs
generate an interrupt request to the CPU together.
The registers definition shows that the AND or OR conditions are applicable to the same
category of PTDs—ISO, INT, ATL.
When an IRQ is generated, the PTD Done Map registers and the respective V bits will
show which PTDs were completed.
The rules that apply to the IRQ Mask AND or IRQ Mask OR settings are:
The OR mask has a higher priority over the AND mask. An IRQ is generated if bit n of
the done map is set and the corresponding bit n of the OR Mask register is set.
If the OR mask for any done bit is not set, then the AND mask comes into picture. An
IRQ is generated if all the corresponding done bits of the AND Mask register are set.
For example: If bits 2, 4 and 10 are set in the AND Mask register, an IRQ is generated
only if bits 2, 4, 10 of the done map are set.
If using the IRQ interval setting for the bulk PTD, an interrupt will only occur at the
regular time interval as programmed in the ATL Done Timeout register. Even if an
interrupt event occurs before the timeout of the register, no IRQ will be generated until
the time is up.
For an example on using the IRQ Mask AND or IRQ Mask OR registers without the ATL
Done Timeout register, see
Table 4
.
The AND function: Activate the IRQ only if PTDs 1, 2 and 4 are done.
The OR function: If any of the PTDs 7, 8 or 9 are done, an IRQ for each of the PTD will be
raised.
7.5 Phase-Locked Loop (PLL) clock multiplier
The internal PLL requires a 12 MHz input, which can be a 12 MHz crystal or a 12 MHz
clock already existing in the system with a precision better than 50 ppm. This allows the
use of a low-cost 12 MHz crystal that also minimizes Electro-Magnetic Interference (EMI).
When an external crystal is used, make sure the CLKIN pin is connected to V
CC(I/O)
.
Table 4:
PTD
1
2
3
4
5
6
7
8
9
Using the IRQ Mask AND or IRQ Mask OR registers
AND register
OR register
1
0
1
0
0
0
1
0
0
0
0
0
0
1
0
1
0
1
Time
1 ms
-
-
3 ms
-
-
5 ms
6 ms
7 ms
PTD done
1
1
-
1
-
-
1
1
1
IRQ
-
-
-
active because of AND
-
-
active because of OR
active because of OR
active because of OR
相關PDF資料
PDF描述
ISP1761 Hi-Speed Universal Serial Bus On-The-Go controller
ISP1761BE Hi-Speed Universal Serial Bus On-The-Go controller
ISP1761ET Hi-Speed Universal Serial Bus On-The-Go controller
ISP2100A Telecommunication IC
ISP2100BN4 Microprocessor
相關代理商/技術參數
參數描述
ISP1760BE 制造商:NXP Semiconductors 功能描述:CONTROLLER USB HOST SMD LQFP128 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB HOST 128LQFP
ISP1760BE,518 功能描述:輸入/輸出控制器接口集成電路 USB HOST CONTROLLER RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
ISP1760BE,551 功能描述:輸入/輸出控制器接口集成電路 USB HS HOST CONTRLLR RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
ISP1760BE,557 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1760BE518 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB HOST 128LQFP