- 您現在的位置：買賣IC網 > PDF目錄379203 > IBM038329NP6B (IBM Microeletronics) 256K x 32 Synchronous Graphics RAM(256K x 32 高性能8M位CMOS同步動態RAM（帶內置的圖形性能）) PDF資料下載
參數資料
| 型號： | IBM038329NP6B |
| 廠商： | IBM Microeletronics |
| 英文描述： | 256K x 32 Synchronous Graphics RAM(256K x 32 高性能8M位CMOS同步動態RAM（帶內置的圖形性能）) |
| 中文描述： | 256K × 32同步圖形RAM（256K × 32位高性能800萬的CMOS同步動態隨機存儲器（帶內置的圖形性能）） |
| 文件頁數： | 31/66頁 |
| 文件大?。?/td> | 952K |
| 代理商： | IBM038329NP6B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
IBM038329NL6B
IBM038329NP6B
256K x 32 Synchronous Graphics RAM
03K4292.E35604
Revised 3/98
IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
Page 31 of 66
Read Command (RD)
The following pages describe in detail the Read operations with the help of timing diagrams for various
cases.
A Read bursts is initiated with a Read command. The starting column address and the bank address are pro-
vided with the Read command and Auto Precharge is either enabled or disabled for that burst access. Upon
completion of a burst, assuming no other commands have been initiated, the DQs will go to High-Z. A Full
Page Burst will continue until terminated (at the end of the page it will wrap to column 0 and continue).
Various cases of Reads are shown. The user can use latencies of one, two or three depending upon the sys-
tem clock. A fixed-length Read Burst may be followed by or truncated with a Write burst or Block Write com-
mand (provided that Auto Precharge was not activated) and a Full Page Read burst may be truncated by a
Write burst or Block Write command. The Write burst may be initiated on the clock edge immediately follow-
ing the last (or last desired) data element from the Read burst, provided that I/O contention can be avoided.
It
is generally a good design practice that a single cycle delay must occur between the last data read
and the Write command.
The DQM inputs can be used to avoid I/O contention as shown in the figure labeled Read Followed by a Write
with Extra Clock Cycle on page 37. The DQMs must be asserted High at least two clocks (DQM latency is two
clocks for output buffers) prior to the Write command to suppress data-out due to the previous Read com-
mand. Once the Write command is registered, the output buffers will go to High-Z (or remain High-Z) regard-
less of the state of DQM signals. The DQM signals must be de-asserted (DQM latency is zero clocks for input
buffers) on the same cycle as a Write command to ensure that the written data is not masked. The figure
labeled Read Followed by a Write (or Block Write) on page 36 shows the case where the clock frequency
allows for bus contention to be avoided without adding a NOP cycle, and the one labeled Read Followed by a
Write with Extra Clock Cycle on page 37 shows the case where the additional NOP is needed.
Either a fixed-length or a full-page Read burst can be truncated with a Precharge command to the same
bank. Note that the Precharge command should be issued one cycle before the clock edge at which the last
desired data is valid. A subsequent command cannot be issued to the same bank until t
RP
is met. Part of the
row precharge time is hidden during the access of the last data element. An Auto Precharge command can
be used in place of the Precharge command for fixed length bursts. The disadvantage of the Auto Precharge
command is that it does not truncate fixed-length bursts and does not apply to Full Page Bursts.The disad-
vantage of the Precharge command is that it requires the command and address busses to be available at
the appropriate time to issue the command.
Either a fixed-length or a full-page Read burst can be terminated with the Burst Terminate command. The
fixed-length Burst with Auto Precharge cannot be truncated by the Burst Terminate command.
The Burst
Terminate command should be issued one cycle before the positive clock edge at which the last
desired data element is valid.
Logic Table for Read Command
Mnemonic
CKE
CS
RAS
CAS
WE
DSF
DQM
BA (A9)
A8
A7-A0
RD
H
L
H
L
H
L
0/1
BS
L
Column
RDA
H
L
H
L
H
L
0/1
BS
H
Column
相關PDF資料 |
PDF描述 |
|---|---|
| IBM041812PQKB | 64K X 18 BURST SRAM(64K X 18高性能可猝發同步CMOS靜態RAM) |
| IBM041813PPLB | 64K X 18 BURST PIPELINE SRAM(1M (64K X 18)同步可猝發流水線式線式高性能靜態RAM) |
| IBM041813PQKB | 64K X 18 Burst Pipeline SRAM(1M（64K X 18）高性能同步可猝發管線式靜態RAM) |
| IBM041814PPLB | 64K X 18 BURST SRAM(1M (64K X 18)同步可猝發高性能靜態RAM) |
| IBM041814PQKB | 64K X 18 BURST SRAM(1M（64K X 18）高性能同步可猝發CMOS靜態RAM) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBM038329NQ6A-7R5 | 制造商:IBM 功能描述: |
| IBM041812PQKB10 | 制造商:IBM 功能描述:* |
| IBM041812PQKB11 | 制造商:IBM 功能描述:* |
| IBM041813PQKB5 | 制造商:IBM 功能描述: |
| IBM0418A4ACLAA-4F | 制造商:IBM 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。