- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C970A (Advanced Micro Devices, Inc.) PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product PDF資料下載
參數資料
| 型號： | AM79C970A |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| 中文描述： | PCnet - 2的PCI單芯片全雙工以太網控制器，適用于PCI總線產品 |
| 文件頁數： | 72/219頁 |
| 文件大小： | 1065K |
| 代理商： | AM79C970A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁當前第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁
AMD
P R E L I M I N A R Y
72
Am79C970A
update the current RDTE status with the end of frame
(ENP) indication set, write the message byte count
(MCNT) for the entire frame into RMD2 and overwrite
the “current” entries in the CSRs with the “next” entries.
Media Access Control
The Media Access Control (MAC) engine incorporates
the essential protocol requirements for operation of a
compliant Ethernet/802.3 node, and provides the inter-
face between the FIFO sub-system and the Manchester
Encoder/Decoder (MENDEC).
This section describes operation of the MAC engine
when operating in half-duplex mode. When operating in
half-duplex mode, the MAC engine is fully compliant to
Section 4 of ISO/IEC 8802-3 (ANSI/IEEE Standard
1990 Second Edition) and ANSI/IEEE 802.3 (1985).
When operating in full-duplex mode, the MAC engine
behavior changes as described in the section
“Full-Duplex Operation”.
The MAC engine provides programmable enhanced
features designed to minimize host supervision, bus
utilization, and pre- or post- message processing.
These include the ability to disable retries after a colli-
sion, dynamic FCS generation on a frame-by-frame ba-
sis, automatic pad field insertion and deletion to enforce
minimum frame size attributes, automatic re-transmis-
sion without reloading the FIFO, and automatic deletion
of collision fragments.
The two primary attributes of the MAC engine are:
I
Transmit and receive message data encapsulation
— Framing (frame boundary delimitation, frame
synchronization)
— Addressing (source and destination address
handling)
— Error detection (physical medium transmission
errors)
I
Media Access Management
— Medium allocation (collision avoidance)
— Contention resolution (collision handling)
Transmit and Receive Message Data
Encapsulation
The MAC engine provides minimum frame size enforce-
ment for transmit and receive frames. When
APAD_XMT (CSR, bit 11) is set to ONE, transmit mes-
sages will be padded with sufficient bytes (containing
00h) to ensure that the receiving station will observe an
information field (destination address, source address,
length/type, data and FCS) of 64 bytes. When
ASTRP_RCV (CSR4, bit 10) is set to ONE, the receiver
will automatically strip pad bytes from the received mes-
sage by observing the value in the length field, and strip-
ping excess bytes if this value is below the minimum
data size (46 bytes). Both features can be
independently over-ridden to allow illegally short (less
than 64 bytes of frame data) messages to be transmitted
and/or received. The use of this feature reduces bus
utilization because the pad bytes are not transferred into
or out of main memory.
Framing
The MAC engine will autonomously handle the con-
struction of the transmit frame. Once the transmit FIFO
has been filled to the predetermined threshold (set by
XMTSP in CSR80), and access to the channel is cur-
rently permitted, the MAC engine will commence the 7
byte preamble sequence (10101010b, where first bit
transmitted is a 1). The MAC engine will subsequently
append the Start Frame Delimiter (SFD) byte
(10101011b) followed by the serialized data from the
transmit FIFO. Once the data has been completed, the
MAC engine will append the FCS (most significant bit
first) which was computed on the entire data portion of
the frame. The data portion of the frame consists of des-
tination address, source address, length/type, and
frame data. The user is responsible for the correct order-
ing and content in each of these fields in the frame.
The receive section of the MAC engine will detect an in-
coming preamble sequence and lock to the encoded
clock. The internal MENDEC will decode the serial bit
stream and present this to the MAC engine. The MAC
will discard the first 8 bits of information before search-
ing for the SFD sequence. Once the SFD is detected, all
subsequent bits are treated as part of the frame. The
MAC engine will inspect the length field to ensure mini-
mum frame size, strip unnecessary pad characters (if
enabled), and pass the remaining bytes through the re-
ceive FIFO to the host. If pad stripping is performed, the
MAC engine will also strip the received FCS bytes, al-
though normal FCS computation and checking will oc-
cur. Note that apart from pad stripping, the frame will be
passed unmodified to the host. If the length field has a
value of 46 or greater, all frame bytes including FCS will
be passed unmodified to the receive buffer, regardless
of the actual frame length.
If the frame terminates or suffers a collision before 64
bytes of information (after SFD) have been received, the
MAC engine will automatically delete the frame from
the receive FIFO, without host intervention. The
PCnet-PCI II controller has the ability to accept
runt
packets
for
diagnostics
proprietary networks.
purposes
and
Destination Address Handling
The first 6 bytes of information after SFD will be inter-
preted as the destination address field. The MAC engine
provides facilities for physical (unicast), logical (multi-
cast) and broadcast address reception.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C970AVCW | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970 | PCnetTM-PCI Single-Chip Ethernet Controller for PCI Local Bus |
| AM79C971VCW | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
| AM79C971 | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
| AM79C971KCW | IC LOGIC 16211 24-BIT FET BUS SWITCH -40+85C TSSOP-56 35/TUBE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C970AKC | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AKC\\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Advanced Micro Devices 功能描述: |
| AM79C970AKC\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM79C970AKCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
發布緊急采購，3分鐘左右您將得到回復。