- 您現在的位置：買賣IC網 > PDF目錄375267 > ADSP-2191 (Analog Devices, Inc.) DSP Microcomputer PDF資料下載
參數資料
| 型號： | ADSP-2191 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 數字信號處理 |
| 英文描述： | DSP Microcomputer |
| 中文描述： | DSP微機 |
| 文件頁數： | 12/52頁 |
| 文件大小： | 1873K |
| 代理商： | ADSP-2191 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
ADSP-2191M
–12–
REV. 0
The OPMODE, BMODE1, and BMODE0 pins, sampled
during hardware reset, and three bits in the Reset Configuration
Register implement these modes:
Execute from memory external 16 bits—The memory
boot routine located in boot ROM memory space
executes a boot-stream-formatted program located at
address 0x010000 of boot memory space, packing 16-bit
external data into 24-bit internal data. The External Port
Interface is configured for the default clock multiplier
(128) and read waitstates (7).
Boot from EPROM—The EPROM boot routine located
in boot ROM memory space fetches a boot-stream-for-
matted program located at physical address 0x00 0000 of
boot memory space, packing 8- or 16-bit external data
into 24-bit internal data. The External Port Interface is
configured for the default clock multiplier (32) and read
waitstates (7).
Boot from Host—The (8- or 16-bit) Host downloads a
boot-stream-formatted program to internal or external
memory. The Host’s boot routine is located in internal
ROM memory space and uses the top 16 locations of
Page 0 program memory and the top 272 locations of
Page 0 data memory.
The internal boot ROM sets semaphore A (an IO register
within the Host port) and then polls until the semaphore
is reset. Once detected, the internal boot ROM will remap
the interrupt vector table to Page 0 internal memory and
jump to address 0x00 0000 internal memory. From the
point of view of the host interface, an external host has
full control of the DSP's memory map. The Host has the
freedom to directly write internal memory, external
memory, and internal I/O memory space. The DSP core
execution is held off until the Host clears the semaphore
register. This strategy allows the maximum flexibility for
the Host to boot in the program and data code, by leaving
it up to the programmer.
Execute from memory external 8 bits (No Boot)—
Execution starts from Page 1 of external memory space,
packing either 8- or 16-bit external data into 24-bit
internal data. The External Port Interface is config-
ured for the default clock multiplier (128) and read
waitstates (7).
Boot from UART—The Host downloads
boot-stream-formatted program using an autobaud
handshake sequence. The Host agent selects a baud rate
within the UART’s clocking capabilities. After a hardware
reset, the DSP’s UART expects a 0xAA character (eight
bits data, one start bit, one stop bit, no parity bit) on the
RXD pin to determine the bit rate; and then replies with
an OK string. Once the host receives this OK it downloads
the boot stream without further handshake.The UART
boot routine is located in internal ROM memory space
and uses the top 16 locations of Page 0 program memory
and the top 272 locations of Page 0 data memory.
Boot from SPI, up to 4K bits—The SPI0 port uses the
SPI0SEL1 (reconfigured PF2) output pin to select a
single serial EEPROM device, submits a read command
at address 0x00, and begins clocking consecutive data into
internal or external memory. Use only SPI-compatible
EEPROMs of
≤
4K bit (12-bit address range). The SPI0
boot routine located in internal ROM memory space
executes a boot-stream-formatted program, using the top
16 locations of Page 0 program memory and the top 272
locations of Page 0 data memory. The SPI boot configu-
ration is SPIBAUD0=60 (decimal), CPHA=1, CPOL=1,
8-bit data, and MSB first.
Boot from SPI, from >4K bits to 512K bits—The SPI0
port uses the SPI0SEL1 (re-configured PF2) output pin
to select a single serial EEPROM device, submits a read
command at address 0x00, and begins clocking consecu-
tive data into internal or external memory. Use only
SPI-compatible EEPROMs of
≥
4K bit (16-bit address
range). The SPI0 boot routine, located in internal ROM
memory space, executes a boot-stream-formatted
program, using the top 16 locations of Page 0 program
memory and the top 272 locations of Page 0 data memory.
As indicated in
Table 6
, the OPMODE pin has a dual role, acting
as a boot mode select during reset and determining SPORT or
SPI operation at runtime. If the OPMODE pin at reset is the
opposite of what is needed in an application during runtime, the
application needs to set the OPMODE bit appropriately during
runtime prior to using the corresponding peripheral.
Bus Request and Bus Grant
The ADSP-2191M can relinquish control of the data and address
buses to an external device. When the external device requires
access to the bus, it asserts the bus request (
BR
) signal. The (
BR
)
signal is arbitrated with core and peripheral requests. External
Bus requests have the lowest priority. If no other internal request
is pending, the external bus request will be granted. Because of
Table 6. Select Boot Mode (OPMODE, BMODE1, and
BMODE0)
O
B
B
Function
0
0
0
Execute from external memory 16 bits
(No Boot)
Boot from EPROM
Boot from Host
Reserved
Execute from external memory 8 bits
(No Boot)
Boot from UART
Boot from SPI, up to 4K bits
Boot from SPI, >4K bits up to
512K bits
0
0
0
1
0
1
1
0
1
0
1
0
1
1
1
0
1
1
1
0
1
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-2191M | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| ADSP-2191MBCA-140 | DSP Microcomputer |
| ADSP-2191MKCA-160 | DSP Microcomputer |
| ADSP-2191MKST-160 | DSP Microcomputer |
| ADSP-2192 | DSP Microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-219122MKST-160 | 制造商:Analog Devices 功能描述: |
| ADSP-2191MBCA-140 | 功能描述:IC DSP CONTROLLER 16BIT 144MBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-2191MBCAZ-140 | 功能描述:IC DSP CONTROLLER 16BIT 144MBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-2191MBST-140 | 制造商:Analog Devices 功能描述:DSP 16-Bit 140MHz 140MIPS 144-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| ADSP-2191MBSTZ-140 | 功能描述:IC DSP CONTROLLER 16BIT 144LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。